Descargar Imprimir esta página

EAS ELECTRIC EMD090W Manual De Instrucciones página 18

Publicidad

Idiomas disponibles

Idiomas disponibles

Dishwasher Features
1
2
3
4
5
6
4.Prior Using for the First Time
Before using your dishwasher for the first time:
A. Set the water softener
B. Loading the salt into the softener
C. Fill the rinse aid dispenser
D. Fill in detergent
A. Set the Water Softener
The water softener is designed to remove minerals and salts from the water, which would have a
detrimental or adverse effect on the operation of the appliance. The higher the content of these
minerals and salts, the harder the water is. The softener should be adjusted according to the
hardness of the water in your area. Your local Water Authority can advise you on the hardness of
the water in your area.
Setting
The amount of salt dispensed can be set from H0 to H7.
Salt is not required at the set value H0.
1. Find out about the hardness value of your tap water. Your water utility company will help you
with this.
2. Set value can be found in the water hardness table.
3. Close the door.
4. Switch on "Power" switch.
5. Hold down " Delay" button and then press "Program" button for 5 seconds.The buzzer rings
one time and H..
flashes on the digital display.(factory setting is H4)
4
Front View
1 Upper Basket
2 Spray Arms
3 Lower Basket
4 Water Softener
8
5 Filters
6 Detergent Dispenser
7 Rinse Aid Dispenser
8 Cutlery basket
7
To change the setting:
1. Press " Delay " button.
Each time the button is pressed, the set value
increasesby one level;when the value of H7 has
been reached, the display jumps back to H0(off).
2. Press " Program " button. The chosen setting
has now been stored.
Contact your local water board for infor-
mation on the hardness of your water
supply.
B. Loading the Salt into the Softener
Always use salt intended for use with dishwasher.
NOTE: If your model has no water softener, you may skip this section
The hardness of the water varies from place to place. If hard water is used in the
dishwasher, deposits will form on the dishes and utensils.
The appliance is equipped with a special softener that uses salts specifically
designed to eliminate lime and minerals from the water.
The salt container is located beneath the lower basket and should be filled as follows:
Attention!
Only use salt specifically designed for use in dishwashers! All other types of salt not specifically
designed for use in a dishwasher, especially table salt, will damage the water softener. In case of
damages caused by the use of unsuitable salt the manufacturer does not give any warranty nor is
liable for any caused damages.
Only fill with salt just before starting one of the complete washing programmes.
This will prevent any grains of salt or salty water, which may have been split, remaining on the
bottom of the machine for any period of time, which may cause corrosion.
After the first wash cycle the control panel light expires.
1
A. Remove the lower basket and then unscrew and remove the cap from the salt container.
B. If you are filling the container for the first time, fill 2/3 of its volume with water (around 500ml).
V.1
V.1
Water hardness table
Water hardness
Mmol/l
Clark
Range
0-8
soft
0-1.1
9-10
soft
1.2-1.4
11-12
medium
1.5-1.8
13-15
medium
1.9-2.1
16-20
medium
2.2-2.9
21-26
hard
3.0-3.7
27-38
hard
3.8-5.4
39-62
hard
5.5-8.9
WATER SOFTENER
2
Set value on
the machine
H0
H1
H2
H3
H4
H5
H6
H7
1
2
5

Publicidad

loading

Este manual también es adecuado para:

Emd090x