Publicidad
Idiomas disponibles
Idiomas disponibles
3. Attach the upper push bar on the lower push bar
with one quick-release lever (5), one fixation slice
(g), one washer (b) and one plastic nut (f) each on
both sides (Fig. 4-5). Note the correct alignment
of the quick-release lever fixation slice ensuring
the quick-release function remains intact.
4. Insert the pull start handle (17) in the designated
hook as shown in Fig. 6.
5. Fix the cables to the push bar with the cable clips
(18) provided (Fig. 7).
6. Grass box (16) - open it up and click the plastic
clips into position on the frame (Fig. 8).
7. Mowing with grass box:
Lift the discharge flap (15) with one hand and
hang the grass box (16) as shown in Fig. 9.
8. Mulching:
If the grass box (16) is attached, remove it and
replace it with the mulch insert (19) as shown in
Fig. 10-12.
Setting the cutting height
m CAUTION!
Adjust the cutting height only when the engine is
switched off and the plug boot has been pulled.
• Before you begin to mow, check to ensure that the
blade is not blunt and that none of the fasteners are
damaged.
• To prevent any imbalance, replace blunt and/or
damaged blades as a set only (if applicable). To
carry out this check, first switch off the engine and
pull the spark plug boot.
• The cutting height is centrally adjusted with the cut-
ting height adjustor lever (Fig.13/ Item 14). 5 differ-
ent cutting heights can be selected.
• Pull the adjustor lever out and select the desired
cutting height. The lever snaps into the desired po-
sition. (Fig. 13)
Preparing the area to be mowed
Before mowing, carefully examine the area. Remove
stones, sticks, bones, wires, toys and other objects
that may be ejected.
8. Operation
m CAUTION!
The engine does not come with oil in it. There-
fore, ensure that you add 0,45 liters of oil before
starting it up. Use normal, multigrade oil (SAE30).
The oil level in the engine must be checked each
time before mowing.
You will also need to fill in petrol, as this is also
not supplied upon delivery.
• In order to avoid any unintentional start-ups
of the lawn mower, it comes equipped with an
engine brake (Fig. 1/ Item 3) which must be
pulled back before the engine can be started.
www.scheppach.com service@scheppach.com +(49)-08223-4002-99 +(49)-08223-4002-58
www.scheppach.com service@scheppach.com +(49)-08223-4002-99 +(49)-08223-4002-58
When the engine control lever is released it must
return to its initial position, at which point the engine
automatically switches off.
• Press the engine brake lever (3) together and give
the starter cord (17) a vigorous pull. (Fig. 14)
Attention: When you pull the starting rope the cutting
blade rotates even when dissolved motor brake lever.
Make sure that there are no body parts in danger
zone of cutting blade.
• When the engine is running, press the drive lever
(2) to the handle (1) in order to engage drive on the
mower.
• Before you start mowing, you should run through
this operation several times in order to ensure that
the machine is working properly.
m WARNING
Whenever you need to perform any kind of ad-
justment and/or repair work on your lawn mower,
wait until the blade has come to a complete stop.
Always switch off the engine before carrying out
any adjustments, maintenance or repairs.
m Note!
Using the drive:
• Engine brake (3): Use the lever to stop the engine.
When you release the lever the engine and the
blade stop automatically.
• To mow, hold the drive lever (2) in the working po-
sition. Before you start to mow, check the start/
stop lever several times to be sure that it is work-
ing properly. Ensure that the tension cable can be
smoothly operated (i.e. is not catching or kinking in
any way).
• Drive lever (2):
If you press this the clutch for the drive will be
closed and the lawnmower will start to move with
the motor running. Release the drive lever in good
time to stop the moving lawnmower. Practice start-
ing and stopping before you use the mower for the
first time until you are familiar with controlling the
mower.
Caution: The blade begins to rotate as soon as the
engine is started.
Important: Before you start the engine, move the
motor brake several times to be sure that the stop
cable is properly working. Note: The engine is factory
set to a speed that is optimal for cutting and blowing
grass into the basket and is designed to provide many
years of use.
• Check the oil level.
Open the fuel tank cap and fill the petrol tank (6)
up to the lower point of the tank inlet with about 0.8
litres of petrol. Use a funnel and a measuring con-
tainer for filling. Do not overfill the tank. Use fresh,
clean unleaded fuel.
Never mix oil with petrol. Buy fuel in amounts which
can be used within 30 days in order to guarantee
its freshness.
25 | GB
Publicidad
