Scheppach SM150L Traduccion Del Manual De Instrucciones Originale página 22

6. Technical Data
Dimensions L x W x H
ø grinding disc max.
left/right
ø grinding disc min. left/
right (after wear and tear)
ø grinding disc bore max.
grinding disc width left/
right
Lamp
Weight
Motor
Input power S2 10 min
Motor speed
Subject to technical changes!
Load factor:
A load factor of S2 10 min (intermittent periodic duty)
means that you may operate the motor continuously
at its nominal power level (400 W) for no longer than
10 minutes ON period. If you fail to observe this time
limit the motor will overheat. During the OFF period
the motor will cool again to its starting temperature.
Sound and vibration
Sound and vibration values were measured in ac-
cordance with EN 61029.
L sound pressure level
pA
K uncertainty
pA
L sound power level
WA
K uncertainty
WA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions)
determined in accordance with EN 61029.
Vibration emission value a
h
K uncertainty = 1.5 m/s
2
Warning!
The specified vibration value was established in ac-
cordance with a standardized testing method. It may
change according to how the electric equipment is
used and may exceed the specified value in excep-
tional circumstances.
The specified vibration value can be used to com-
pare the equipment with other electric powertools.
The specified vibration value can be used for initial
assessment of a harmful effect.
22 | GB
380 x 210 x 280 mm
150 mm
110 mm
12,7 mm
20 / 20 mm
LED with battery (2x)
7 kg
230-240 V / 50 Hz
400 W
2850 1/min
64,9 dB(A)
3 dB
76,1 dB(A)
3 dB
≤ 2.5 m/s
2
www.scheppach.com
Keep the noise emissions and vibrations to a
minimum.
• Only use appliances which are in perfect work-
ing order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.
7. Assembly
Before you connect the equipment to the mains sup-
ply make sure that the data on the rating plate are
identical to the mains data.
Always pull the power plug before making adjust-
ments to the equipment.
Pull the power plug before doing any mainte-
nance or assembly work on the equipment.
• The machine must be set up so that it stands firm-
ly, i.e. it must be securely screwed to a work bench
or similar.
• All covers and safety devices have to be properly
fitted before the equipment is switched on.
• The grinding wheels must rotat freely.
• Check that the voltage on the rating plate is the
same as your supply voltage before you connect
the equiment to the power supply.
Warning! Never connect the plug to power source
outlet until all installations and adjustments are com-
pleted and you have read and understood the safety
and operation instructions.
Tool support (left and right) (Fig. 1, 2, 2.1)
Fasten the tool support (4) to the grinding wheel
guard (6) with the mushroom head screw (M6x10) (a)
and the star grip nut (b).
The distance between wheel and work rest should
not exceed 2 mm.
Spark guard with LED work lamp (left and right)
(Fig. 1, 3)
Fasten the spark guard (2) with LED work lamps (5)
to the grinding wheel guard (6) with two M5x8 pan
head screws (c).
The distance to the grinding wheel (3) should be not
more than 2 mm. The distance between the spark
guard (2) and the grinding wheel (3) can be adjusted
by slackening the two pan head screws (c). Tighten
the screws securely.
LED work lamp (Fig. 1, 4, 4.1, 4.2)
The lighting (5) can be switched on by pressing the
switch (d) on the lamp. The lighting is switched off
by pressing the switch again.