Forch 5326 125 1 Manual Del Usuario página 67

Using an Extension Cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor
2
size is 1 mm ; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
serious personal injury, turn tool off
and disconnect tool from power source
before making any adjustments or
removing/installing attachments or
accessories. Before reconnecting the
tool, depress and release the trigger
switch to ensure that the tool is off.
Attaching Side Handle (fi g. 1, 6)
WARNING: Before using the tool, check
that the handle is tightened securely.
Screw the side handle (d) tightly into one of the
holes (f) on either side of the gear case.
Mounting and Removing the Guard
(fi g. 2)
WARNING: To reduce the risk of
serious personal injury, turn tool off
and disconnect tool from power source
before making any adjustments or
removing/installing attachments or
accessories. Before reconnecting the
tool, depress and release the trigger
switch to ensure that the tool is off.
CAUTION: Guards must be used with this
grinder.
When using the 5326 125 1 / 5326 125 2 grinder
for cutting metal or masonry a Type 1 guard
MUST be used. Type 1 guards are available at
extra cost from Förch distributors.
NOTE: Please refer to the Grinding and Cutting
Accessory Chart at the end of this section to
show other accessories that can be used with
these grinders.
GUARD WITH FIXING SCREW (FIG. 2)
5326 125 2
1. Place the angle grinder on a table, spindle (o)
up.
2. Align the lugs (k) with the notches (l).
3. Press the guard (c) down and rotate it to the
required position.
4. Securely tighten the screw (m).
5. To remove the guard, slacken the screw.
CAUTION: If the guard cannot be
tightened by the adjusting screw, do not
use the tool. To reduce the risk of personal
injury, take the tool and guard to a service
center to repair or replace the guard.
QUICK ADJUSTMENT OF SAFETY COVER
WITHOUT TOOLS (FIG. 3)
5326 125 1
1. Place the angle grinder on a table, spindle (o)
up.
2. Release the clamping lock (g) and hold the
guard (c) over the tool as shown.
3. Align the lugs (k) with the notches (l).
4. Press the guard down and rotate it to the
required position.
5. If required, increase the clamping force by
tightening the screw (m).
6. Tighten the clamping lock.
7. To remove the guard, release the clamping
lock.
Fitting and Removing a Grinding or
Cutting Disc (fi g. 1, 4, 5)
WARNING: Do not use a damaged disc.
1. Place the tool on a table, guard up.
2. Fit the backing fl ange (i) correctly onto the
spindle (o) (fi g. 4).
3. Place the disc (n) on the backing fl ange (i).
When fi tting a disc with a raised center, make
sure that the raised centre (j) is facing the
backing fl ange (i).
4. Screw the threaded clamp nut (h) onto the
spindle (o) (fi g. 5):
a. The ring on the threaded clamp nut (h)
must face towards the disc when fi tting
a grinding disc (fi g. 5A);
b. The ring on the threaded clamp nut (h)
must face away from the disc when fi tting
a cutting disc (fi g. 5B).
5. Press the spindle lock button (b) and rotate the
spindle (o) until it locks in position.
6. Tighten the threaded clamp nut (h) with the
two-pin spanner supplied.
7. Release the spindle lock.
8. To remove the disc, loosen the threaded clamp
nut (h) with the two-pin spanner.
E N G L I S H
67