Descargar Imprimir esta página
Sauder Rollingwood Serie Instrucciones De Montaje
Ocultar thumbs Ver también para Rollingwood Serie:

Publicidad

Enlaces rápidos

CONTACT US FIRST
CONTACT US FIRST
sauder.com
sauder.com
sauder.com
BEFORE MAKING ANY RETURNS TO THE STORE.
BEFORE MAKING ANY RETURNS TO THE RETAILER.
sauder.com/service
Visit
Prefer the phone? Give us a ring at
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Library Base
Rollingwood Collection | Model 431439
Sauder.com
Share your journey!
to order replacement parts, view video assembly tips, or chat with a live rep.
1-800-445-1527
.
For things 'n such.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-39
Français pg 40-44
Español pg 45-49
Lot # 580092
Purchased: __________________
03/24/22

Publicidad

loading

Resumen de contenidos para Sauder Rollingwood Serie

  • Página 1 CONTACT US FIRST CONTACT US FIRST sauder.com sauder.com sauder.com BEFORE MAKING ANY RETURNS TO THE STORE. BEFORE MAKING ANY RETURNS TO THE RETAILER. sauder.com/service Visit to order replacement parts, view video assembly tips, or chat with a live rep. 1-800-445-1527 Prefer the phone? Give us a ring at Customer Service is available Monday-Friday - 9 a.m.
  • Página 2 Table of Contents Assembly Tools Required Part Identification No. 2 Phillips Screwdriver Hardware Identification Tip Shown Actual Size Hardware Usage Guide Assembly Steps 6-39 Hammer Not actual size Français 40-44 Español 45-49 Safety Warranty Page 2 www.sauder.com/service 431439...
  • Página 3 RIGHT DRAWER SIDE (1) AA SIDE SKIRT (2) RIGHT END (1) DRAWER FRONT (1) BB RIGHT FRONT/LEFT REAR SKIRT (2) DOOR (2) LEFT DRAWER SIDE (1) CC LEFT FRONT/RIGHT REAR SKIRT (2) ADJUSTABLE SHELF (1) W DRAWER BACK (1) 431439 www.sauder.com/service Page 3...
  • Página 4 NAIL - 20 CARD - 6 CARD - 1 1-1/2" FLAT HEAD SCREW - 10 1-3/16" MACHINE SCREW - 1 3/4" MACHINE SCREW - 4 1/2" PAN HEAD SCREW - 12 1/2" FLAT HEAD SCREW - 8 Page 4 www.sauder.com/service 431439...
  • Página 5 The arrow in the HIDDEN CAM must point Arrow toward the hole in the edge of the board. Hidden Cam Hole Insert the CAM SCREW or CAM DOWEL into the HIDDEN CAM. Tighten the HIDDEN CAM. 431439 www.sauder.com/service Page 5...
  • Página 6 Step 1 Look for this icon. It means a video assembly tip is available at www.sauder.com/service/tips Find the numbered video or scan the QR code. å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
  • Página 7 Step 2 å Fasten two HINGE BRACKETS (12) to the RIGHT END (E) exactly as shown. Use the SCREWS in the BRACKETS. Remember: Righty tighty. Lefty loosey. 431439 www.sauder.com/service Page 7...
  • Página 8 Step 3 å Turn five CAM SCREWS (4) into one FRONT END MOLDING (L) and one REAR END MOLDING (M). Page 8 www.sauder.com/service 431439...
  • Página 9 å Fasten the END MOLDINGS (L and M) to the RIGHT END (E). Tighten five HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS in the END insert into the MOLDINGS. These surfaces should be even. 431439 www.sauder.com/service Page 9...
  • Página 10 NOTE: The EXTENSION SLIDES will be used later for the DRAWER. Push the black lever and pull the SLIDE from the RAIL. 1/2" PAN HEAD SCREW (3 used in this step) Open end The HINGE BRACKETS must be here. Page 10 www.sauder.com/service 431439...
  • Página 11 Step 6 å Turn seven CAM SCREWS (4) into the TOP (A). å Push three LARGE HIDDEN CAMS (3) into the TOP MOLDING (O). å Insert two WOOD DOWELS (5) into the TOP MOLDING (O). Arrow 431439 www.sauder.com/service Page 11...
  • Página 12 HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS in the MOLDING insert into the TOP. C A M D E N H I D w i t h f a c e S u r Page 12 www.sauder.com/service 431439...
  • Página 13 Do not stand the unit upright without the å NOTE: Be sure the WOOD DOWELS in the END insert BACK fastened. The unit may collapse. into the TOP. S u r f a c i t h H I D D E N 431439 www.sauder.com/service Page 13...
  • Página 14 Step 9 å Push seven LARGE HIDDEN CAMS (3) into the LEFT END (D). å Insert eight WOOD DOWELS (5) into the edges of the LEFT END (D). (7 used) Arrow Arrow (8 used) Arrow Page 14 www.sauder.com/service 431439...
  • Página 15 Step 10 å Fasten two HINGE BRACKETS (12) to the LEFT END (D) exactly as shown. Use the SCREWS in the BRACKETS. 431439 www.sauder.com/service Page 15...
  • Página 16 Step 11 å Turn five CAM SCREWS (4) into the remaining FRONT END MOLDING (L) and REAR END MOLDING (M). Page 16 www.sauder.com/service 431439...
  • Página 17 å Fasten the END MOLDINGS (L and M) to the LEFT END (D). Tighten five HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS in the END insert into the MOLDINGS. These surfaces should be even. 431439 www.sauder.com/service Page 17...
  • Página 18 EXTENSION RAIL in to find the other holes that line up with the holes in the END. Turn a SCREW into these holes. 1/2" PAN HEAD SCREW (3 used in this step) Open end Page 18 www.sauder.com/service 431439...
  • Página 19 Fasten the LEFT END (D) to the TOP (A). Tighten two HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS in the END insert into the TOP. S u r f a c i t h o u t H I D D 431439 www.sauder.com/service Page 19...
  • Página 20 Step 15 å Turn eight CAMS SCREWS (4) into the BOTTOM (B). Don't worry. It isn't Rome. This can be built in a day. Page 20 www.sauder.com/service 431439...
  • Página 21 1-1/2" FLAT HEAD SCREWS (18). å NOTE: Be sure the WOOD DOWELS in the ENDS insert into the BOTTOM. Curved edge i t h f a c S u r 1-1/2" FLAT HEAD SCREW (4 used in this step) 431439 www.sauder.com/service Page 21...
  • Página 22 Push four LARGE HIDDEN CAMS (3) into one of the SIDE SKIRTS (AA). å Insert four WOOD DOWELS (5) into the SIDE SKIRT (AA). å Repeat this step for the remaining SIDE SKIRT (AA). (8 used) Arrow (8 used) Arrow Arrow Page 22 www.sauder.com/service 431439...
  • Página 23 Insert two WOOD DOWELS (5) into the edges of the SKIRTS (BB and CC). å Turn two CAM SCREWS (4) into the SKIRTS (BB and CC). å Repeat this step for the remaining set of SKIRTS (BB and CC). (4 used) (4 used) Arrow Arrow (4 used) 431439 www.sauder.com/service Page 23...
  • Página 24 Tighten four HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS in the SIDE SKIRTS insert into the SKIRTS. These surfaces should be even. These surfaces should be even. These surfaces should be even. These surfaces should be even. Page 24 www.sauder.com/service 431439...
  • Página 25 Step 20 å Fasten the SKIRTS (AA, BB, and CC) to the BOTTOM (B). Tighten eight HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS in the SKIRTS insert into the BOTTOM. 431439 www.sauder.com/service Page 25...
  • Página 26 BACK (C). Push on opposite corners of your unit if needed to make it "square". å Fasten the BACK (C) to your unit using the NAILS (17). NAIL Notch (20 used in this step) Page 26 www.sauder.com/service 431439...
  • Página 27 Step 22 å Push six SMALL HIDDEN CAMS (6) into the DRAWER SIDES (Q and U) and DRAWER BRACE (Y). å Turn six DRAWER CAM SCREWS (7) into the DRAWER FRONT (T). Arrow 431439 www.sauder.com/service Page 27...
  • Página 28 Step 23 å Fasten the DRAWER SIDES (Q and U) and DRAWER BRACE (Y) to the DRAWER FRONT (T). Tighten six HIDDEN CAMS. Groove Surface without HIDDEN CAMS Page 28 www.sauder.com/service 431439...
  • Página 29 å NOTE: You should start each SCREW a few turns before completely tightening any of them. 1-1/2" FLAT HEAD SCREW (6 used in this step) Be sure the DRAWER BOTTOM inserts into the DRAWER BACK groove. 431439 www.sauder.com/service Page 29...
  • Página 30 Step 25 å Fasten the KNOB (11) to the DRAWER FRONT (T). Use one 1-3/16" MACHINE SCREW (19). 1-3/16" MACHINE SCREW (1 used in this step) Page 30 www.sauder.com/service 431439...
  • Página 31 Fasten the EXTENSION SLIDES (2) to the DRAWER SIDES (Q and U). Use six 1/2" PAN HEAD SCREWS (21) in the holes shown. 1/2" PAN HEAD SCREW (6 used in this step) Open end Open end Open end 431439 www.sauder.com/service Page 31...
  • Página 32 SLIDES on the drawer with the EXTENSION RAILS on the unit and push the drawer into the unit until the drawer is fully inserted. The drawer will push in hard until it is all the way in, then it will slide in and out easier. Page 32 www.sauder.com/service 431439...
  • Página 33 Push three LARGE HIDDEN CAMS (3) into the ADJUSTABLE SHELF (H). å Insert two WOOD DOWELS (5) into the edge of the ADJUSTABLE SHELF (H). å Turn three CAM SCREWS (4) into the SHELF MOLDING (Z). Arrow 431439 www.sauder.com/service Page 33...
  • Página 34 Fasten the SHELF MOLDING (Z) to the ADJUSTABLE SHELF (H). Tighten three HIDDEN CAMS. Almost time to å NOTE: Be sure the WOOD DOWELS in the SHELF insert celebrate! With a nap. into the MOLDING. These surfaces should be even. Page 34 www.sauder.com/service 431439...
  • Página 35 Push a RUBBER SLEEVE (9) over one end of each METAL PIN (8). Insert the METAL PINS into the hole locations of your choice in the ENDS (D and E). Set the ADJUSTABLE SHELF (H) onto the METAL PINS. (4 used) 431439 www.sauder.com/service Page 35...
  • Página 36 Step 31 å Fasten four HINGES (13) to the DOORS (G). Use eight 1/2" FLAT HEAD SCREWS (22). 1/2" FLAT HEAD SCREW (8 used in this step) Page 36 www.sauder.com/service 431439...
  • Página 37 MOUNTING SCREW on the HINGE BRACKET. of the HINGE will fit into å Repeat this step for the other DOOR. this slot. This screw will fit into this slot. Then tighten the screw. HINGE BRACKET Stop Mounting screw HINGE 431439 www.sauder.com/service Page 37...
  • Página 38 To adjust the DOOR in or out (depth), loosen the mounting screw one turn and move the DOOR in or out, as needed. Tighten the mounting screw after making adjustments. Mounting screw (depth) Adjusting screw (horizontal) (vertical adjustment) 3/4" MACHINE SCREW (4 used in this step) Page 38 www.sauder.com/service 431439...
  • Página 39 NOTE: Please read the back pages of the instruction booklet for important safety information. å This completes assembly. Clean with a damp cloth. Wipe dry. And to celebrate, why not share your success story at sauder.com or 431439 www.sauder.com/service Page 39...
  • Página 40 REFERENCE DESCRIPTION QUANTITÉ REFERENCE DESCRIPTION QUANTITÉ conserver le livret pour future référence. Pour contacter Sauder en DESSUS ................1 (ENSEMBLE DE GLISSIÈRE ILLUSTRÉ À PART) ce qui concerne cet DESSOUS ................1 GLISSIÈRE D'EXTENSION ........2 élément, faire référence ARRIÈRE ................1 COULISSE D'EXTENSION ........2 au numéro de lot et...
  • Página 41 ÉTAPE 4 l’EXTRÉMITÉ dans le DESSUS. Fixer les MOULURES D'EXTRÉMITÉ (L et M) à l'EXTRÉMITÉ DROITE (E). Serrer cinq EXCENTRIQUES ESCAMOTABLES. REMARQUE : S’ a ssurer d’insérer les CHEVILLES EN BOIS de l’EXTRÉMITÉ dans les MOULURES. 431439 www.sauder.com/service Page 41...
  • Página 42 Faire tourner une VIS dans ces trous. Faire tourner deux VIS D'EXCENTRIQUE (4) dans les PLINTHES (BB et CC). Répéter cette étape pour le jeu de PLINTHES (BB et CC) restant. Page 42 www.sauder.com/service 431439...
  • Página 43 Fixer les CÔTÉS DE TIROIR (Q et U) et l'ENTRETOISE TABLETTE RÉGLABLE (H). DE TIROIR (Y) au DEVANT DE TIROIR (T). Serrer six Faire tourner trois VIS D'EXCENTRIQUE (4) dans la MOULURE EXCENTRIQUES ESCAMOTABLES. DE TABLETTE (Z). 431439 www.sauder.com/service Page 43...
  • Página 44 D'APPLIQUÉS (15) et coller les sur chaque EXCENTRIQUE ESCAMOTABLE visible. REMARQUE : Prière de lire les informations importantes sur la sécurité figurant sur les pages arrière du manuel d’instructions. Ceci complète l'assemblage. Nettoyer avec un tissu humide. Essuyer. Page 44 www.sauder.com/service 431439...
  • Página 45 (JUEGO DE EXTENSIÓN SE MUESTRA POR SEPARADO) su referencia futura. Si necesita ponerse en FONDO .................1 RIEL DE EXTENSIÓN ..........2 contacto con Sauder en DORSO .................1 CORREDERA DE EXTENSIÓN ......2 cuanto a esta unidad, EXTREMO IZQUIERDO ..........1 EXCÉNTRICO ESCONDIDO GRANDE ..32 refiérase al número...
  • Página 46 EXTREMO se inserten en el PANEL SUPERIOR. Fije las MOLDURAS DE EXTREMO (L y M) al EXTREMO DERECHO (E). Apriete cinco EXCÉNTRICOS ESCONDIDOS. NOTA: Asegúrese de que los PASADORES DE MADERA del EXTREMO se inserten en las MOLDURAS. Page 46 www.sauder.com/service 431439...
  • Página 47 Atornille dos BIELAS DE EXCÉNTRICO (4) en EXTREMO. Atornille un TORNILLO dentro de estos agujeros. los FALDONES (BB y CC). Repita este paso para el conjunto restante de FALDONES (BB y CC). 431439 www.sauder.com/service Page 47...
  • Página 48 Fije los LADOS DE CAJÓN (Q y U) y la RIOSTRA ESTANTE AJUSTABLE (H). DE CAJÓN (Y) a la CARA DE CAJÓN (T). Apriete seis Atornille tres BIELAS DE EXCÉNTRICO (4) dentro de la EXCÉNTRICOS ESCONDIDOS. MOLDURA DE ESTANTE (Z). Page 48 www.sauder.com/service 431439...
  • Página 49 APLICACIONES GRANDE (15) y aplique las sobre cada EXCÉNTRICO ESCONDIDO visible. NOTA: Por favor, lea las páginas de atrás del folleto de instrucciones en cuanto a importante información de seguridad. Esto completa el ensamblaje. Limpiar con un trapo húmedo. Seque con un paño. 431439 www.sauder.com/service Page 49...
  • Página 50 Además, el peso y la ubicación del tubo de imagen tienden a causar la inestabilidad de televisores y son propensos a inclinarse hacia adelante. Page 50 www.sauder.com/service 431439...
  • Página 51 à compter de la date d'achat la première fois et qui sont signalés à Sauder dans les limites de couverture de la contre tout défaut de matériaux ou de fabrication des composantes de mobilier Sauder.
  • Página 52 BEFORE MAKING ANY RETURNS TO THE RETAILER. So, how did it go? Dear Valued Customer: Thanks so much for choosing Sauder® furniture. I hope the Set a world record for speed? purchase and assembly process was a positive experience Feeling good about yourself? and you feel good about the furniture you just built.

Este manual también es adecuado para:

Rollingwood 431439