Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH (
Original Instructions)
4. Power Tool Use And Care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
c. Disconnect the plug from the power source and/or
remove the battery, if detachable from the power
tool before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting
the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the power tool's operation. If damaged,
have the power tool repaired before use. Many
accidents are caused by poorly maintained power
tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
h. Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained.
ADDITIONAL SPECIFIC SAFETY RULES
WARNING! Safety Instructions for Sanders
a. Hold power tools by insulated gripping surfaces,
because the sanding surface may contact its
own cord. Cutting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
opertator an electric shock.
b. Warning! Contact with or inhalation of dusts arising
from sanding applications may endanger the health
of the operator and possible bystanders. Wear a dust
mask specifically designed for protection against dust
and fumes and ensure that persons within or entering
the work area are also protected.
14
c. Thoroughly remove all dust after sanding.
d. Take special care when sanding paint which is possibly
lead based or when sanding some woods and metal
which may produce toxic dust:
-
Do not let children or pregnant women enter the work
area.
-
Do not eat, drink or smoke in the work area.
-
Dispose of dust particles and any other debris safely.
Additional Safety Information
WARNING: We recommend the use of a residual
current device with a residual current rating of
30mA or less.
RESIDUAL RISKS
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These are:
– Impairment of hearing
– Risk of personal injury due flying particles.
– Risk of burns due to accessories becoming hot
during operation.
– Risk of personal injury due to prolonged use.
– Risk of dust from hazardous substances.
ELECTRICAL SAFETY
Only one voltage is applicable to this tool. Be sure to check
that the power supply corresponds to the voltage on the
rating plate.
Your Stanley tool is equipped with double
insulation, hence, it does not require to be
earthed.
When the power cord is damaged, have it sent to a
STANLEY service center for replacement to specially
prepared cables.
USING AN EXTENSION CABLE
If an extension cable is required, use an approved 3–core
extension cable suitable for the power input of this tool
(see Technical Data).The minimum conductor size is
1.5 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
LABELS ON TOOL
In addition to the pictographs used in this manual, the
labels on the tool show the following pictographs:
WARNING! To reduce the risk of injury, the
user must read the instruction manual before
use.
Wear safety glasses or goggles.
Publicidad
