Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH (
Original Instructions)
fastening torque is affected by many factors including
the following:
♦ Voltage: Low voltage, due to generator or long
extension cord, will reduce fastening torque.
♦ Accessory size: Failure to use the correct accessory
size will cause a reduction in fastening torque.
♦ Bolt Size: Larger bolt diameters generally require
higher fastening torque. Fastening torque will also
vary according to length, grade, and torque coefficient.
♦ Bolt: Ensure that all threads are free of rust and other
debris to allow proper fastening torque.
♦ Material: The type of material and surface finish of the
material will affect fastening torque.
♦ Fastening Time: Longer fastening time results in
increased fastening torque. Using a longer fastening
time than recommended could cause the fasteners to
be overstressed, stripped or damaged.
Capacity
Your 1/2" (12.7 mm) impact wrench uses sockets with 1/2"
(12.7 mm) square drive ends.
MAINTENANCE
Your STANLEY power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
♦ Regularly clean the ventilation slots in your tool using
a soft brush or dry cloth.
♦ Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.This
machine is not user-serviceable. If problems occur
contact an authorised repair agent.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of the main
housing with dry air as often as dirt is seen
collecting in and around the air vents. Wear
approved eye protection and approved dust mask when
performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the
materials used in these parts. Use a cloth dampened only
with water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
To maintain products SAFETY and RELIABILITY,
repair, carbon brush inspection and replacement, any
other maintenance or adjustment should be performed
by STANLEY Service Centers, always using Stanley
replacement parts.
16
OPTIONAL ACCESSORIES
WARNING: Since accessories, other than those
offered by STANLEY, have not been tested with
this product, use of such accessories with this
tool could be hazardous. To reduce the risk of injury, only
STANLEY, recommended accessories should be used
with this product.
Consult your dealer for further information on the
appropriate accessories.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your STANLEY product
needs replacement, or if it is of no further use to you, do
not dispose of it with household waste. Please sort it out
for separate recycling.
Separate collection of used products and packaging
allows materials to be recycled and used again. Re-
use
of
recycled
environmental pollution and reduces the demand for raw
materials.
NOTES
STANLEY's policy is one of continuous improvement to
our products and as such, we reserve the right to change
product specifications without prior notice.
Standard equipment and accessories may vary by country.
Product specifications may differ by country.
Complete product range may not be available in all
countries. Contact your local STANLEY dealers for range
availability.
SERVICE INFORMATION
STANLEY offers a full network of company-owned and/
or authorized service agents throughout your country.
All STANLEY Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
power tool service. Whether you need technical advice,
repair, or genuine factory replacement parts, contact the
STANLEY location nearest to you.
TECHNICAL DATA
IMPACT WRENCH
TYPE
Voltage
V
Frequency
Hz
Power input
W
Orbits(no load)
.../min
(rpm)
Impact
IPM
Torque max
Nm
Size of anvil
mm
Weight
kg
materials
helps
prevent
SIW901
-AR -B2C -B3
-B2
220
220
120
220
50
50
60
60
820
0-2200
0-2700
610
1/2 Inch (12.7mm)
3.5
-BR
127
60
Publicidad
