About This Document - Wieland SP-COP1 Manual De Instrucciones

INSTRUCTION MANUAL
(Translation of the original instructions)
SP-COP1 / SP-COP2
Main module of the modular
safety controller samos®PRO COMPACT
BA000978 - 02/2016 (Rev. C)
1

About this document

1.1 Documentation for the system samos
This installation manual describes the installation of the controller
module of the configurable safety control samos
The installation of the samos
and SP-SDI, the relay-modules SA-OR-S2-2RK and SA-OR-S1-4RK is
described in separate installation manuals.
Installation, configuration and operation of the configurable
®
safety control samos PRO is described in the system manuals
„samos ® PRO COMPACT Hardware" and „samos
Document Title
®
Manual samos PRO COMPACT Hardware
®
Manual samos PLAN5+ Software
Above all, technical knowledge in the installation of protection on
machinery is necessary, which is not part of this manual.
1.2 Function of this document
This installation manual is intended for
machine builder or machine operator
controller module of the configurable safety control samos
This installation manual is not a manual for the operation of the
machine. Information about that is part of the manual of the
machine.
2 On safety
This chapter is for your safety and the safety of the machine opera-
tor. Please read this chapter carefully before starting the installation.
2.1 Qualified persons
The configurable safety controller samos
qualified persons.
Qualified is, who ...
has an adequate technical education and
is instructed by the machine builder in the operation of the
machine and the significant safety guidelines and
has access to the manuals of samos®PRO COMPACT and has
read and understood these manuals and
has access to the manuals of the protection equipment of the
machine being connected to the configurable safety controller
and has read and understood these manuals.
2.2 Application area of the system
samos®PRO COMPACT is a configurable safety controller for safety
applications and is applicable
according to EN 61508 up to SIL 3
according to EN 62061 up to SIL CL 3
according to EN ISO 13849-1:2006 up to Performance Level (PL) e
according to EN ISO 13849-1 up to category 4
according to 50156-1 up to SNS 3
according to EN 61511
according to EN 81-1/2
The actual level of safety depends on the wiring, the parameteriza-
tion, the switching elements and its installation on the machinery.
The configurable safety control samos®PRO COMPACT is monitoring
tactile switching safety elements (e.g. E-Stop buttons, safety
switches, safety interlocks, lightcurtains, laser scanner) and pro-
cessing their signals. With its safe switching outputs the configura-
ble safety control can switch off actuators (e.g. contactors, magnets,
valves) of machines or plants.
®
PRO
® PRO.
®
PRO expansion modules SP-SDIO
® PLAN5+ Software".
Number
BA000966
BA000968
the technical staff of the
enabling safe installation of the
® PRO.
® PRO has to be installed by
Wieland Electric GmbH
Brennerstr. 10-14
D-96052 Bamberg
www.wieland-electric.com
Printed in Germany
All rights reserved
EN
2.3 Intended operation
The configurable safety control samos®PRO COMPACT is operating
only within its specified operating limits (voltage, temperature etc.,
see technical data and chapter „Application area of the system").
The system has to be operated only by experts and on the machine
on which the system is mounted according to the samos
COMPACT-operation manuals (BA000966 und BA000968) by
qualified staff.
With any different usage or changes of the modules – even for
installation – all warranty claims to Wieland Electric GmbH are lost.
2.4 General safety advices and safety measures
Pay attention to the safety advices and protec-
tion measures!
Notice the following hints in order to guarantee the
intended operation of the configurable safety
WARNING WARNING WARNING WARNING
controller samos®PRO COMPACT.
With installation and operation of the configurable safety control-
ler samos®PRO COMPACT you have to respect the local standards
and directive in your country.
For installation and use of the configurable safety controller
samos®PRO COMPACT and for service and maintenance of the
system national laws and directives are binding, specially
– the EMC-Directive 2014/30/EC
– the Machine Directive 2006/42/EC
– the Safety Requirements of the Work Directive 2009/104/EC
– the Low-voltage-directive 2014/35/EC
– the Lift directive 2014/33/EC
– the Health and safety at Work Act / Safety guidelines.
Manufacturer and operator of the machine, using a configurable
safety controller samos®PRO COMPACT, have to respect all legal-
ly binding safety regulations at their own responsibility in coordi-
nation with the responsible authorities.
All advices and tests described in the manuals must be respected
necessarily.
All tests during the installation have to be made by trained staff
respectively by specially instructed personal and the tests have to
be documented in a comprehensible way.
The external voltage supply of the modules has to bridge gaps of
voltage of 20 ms according to EN 60204. Appropriate power sup-
plies are available from Wieland Electric.
The modules of the system samos
group 1 according to EN 55011.
– The group 1 covers all ISM-devices, where HF-energy is pro-
duced and/or used for the inner function of the device.
The system samos
for class A (Industrial Use) according to
EN 55011!
Therefore samos
WARNING WARNING
WARNING WARNING
the use in the industrial environment and it is not
designed for the use in the private environment.
2.5 Disposal
The disposal of defective modules has to be done in accordance
with the local regulations for waste disposal (e.g. European code for
waste 16 02 14).
®
PRO
®
PRO comply with class A,
® ® ® ®
samos samos samos PRO covers the requirements PRO PRO PRO
® PRO-System is designed only for
7 7 7 7