Descargar Imprimir esta página

Hoover Brave BV71 BV30011 Manual De Instrucciones página 4

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 21
GETTING TO KNOW YOUR CLEANER
A. On/Off Button
M. Carpet and Floor Nozzle (GP) **
B. Bag Door
C. Telescopic Tube Adjuster
D. Telescopic Tube
N. Main Cleaner
E. Suction Regulator
O. Bag Door Release Latch
F. Hose Handle
P. Bag Holder
G. Hose
Q. Pre-motor Filter Frame
H. Bag Check Indicator
R. Pre-motor Filter
I. Cord Rewind Button
S. Exhaust Filter
J. Exhaust Filter Cover
T. Pet Hair Remover Mini Turbo Nozzle*
K. 2 in 1 Tool
U. Allergy Remover Mini Turbo Nozzle*
L. Floor Type Selector*
V. Parquet Nozzle*
ASSEMBLING YOUR CLEANER
Remove all components from the packaging.
1. Connect the hose to the cleaner main body, ensuring it clips and locks into position. [1]
To release: simply press the two buttons on the hose end and pull. [1]
2. Connect the tube upper end to the handle. [2].
3. Connect the tube lower end to the carpet and floor nozzle**.[3]
USING YOUR CLEANER
1. Extract power cord and plug it into the power supply. Do not pull the cord beyond the
red marker. [4]
2. Adjust the length of telescopic tube by moving the telescopic tube adjuster up, and raise
or lower the handle to the most comfortable cleaning position. [5]
3. Carpet and Floor Nozzle**: Press the floor type selector pedal* on the nozzle to select
the ideal cleaning mode for the floor type. [6]
Hard Floor: The brushes are lowered to protect the floor
Carpet: With lifted brushes for the deepest clean
4. Switch the cleaner on by pressing the on/off button on the cleaner main body. [7]
5. Adjust the suction regulator to the desired level. [8]
6. Switch off at the end of use by pressing the on/off button. Unplug and press the cord
rewind button to wind the power cord back into the cleaner. [9]
7. Packing and storage – The tube can be parked for temporary storage while in use, or
in the storage position when not in use. [10]
*Certain Models Only ** Certain models only, nozzles may vary according to model
M1. Carpet Nozzle (CA) **
M2. Hard Floor Nozzle (HF) **
CLEANER MAINTENANCE
Replacing the Dust Bag
If the bag check indicator is red please check and, if necessary, replace the bag.
1. Lift the bag door release latch [11] to open the bag door. Pull the bag holder [12] and
pull the bag collar to remove the bag. [13]
2. Apply the peel and seal sticker, located on the bag collar, to the bag inlet. The full dust
bag should be disposed of correctly and carefully.
3. Fold a new bag as shown on the bag and fit by inserting the collar into the bag holder. [13]
4. Refit the bag holder and close the bag door.
WARNING: The bag door will NOT close if the dust bag and/or the bag holder are not
assembled to the cleaner. Always ensure the bag and bag holder are present when
closing the bag door.
Remember: The bag check indicator may also be red if an obstruction has occurred. In
this case, refer to 'Removing a blockage from the system'.
Cleaning the Filters
To maintain optimum performance of your cleaner, please wash the filters after each 5
bag changes.
Cleaning the pre-motor filter:
1. Lift the bag door release latch [11] to open the bag door and remove the bag. [12]
2. To remove the pre-motor filter, slide the pre-motor filter frame from the cleaner. [14]
3. Remove the filter from the holder. [15]
4. Wash it in hand warm water [18], and allow it to dry thoroughly before replacing it in
the cleaner. [19]
Cleaning the exhaust filter:
1. To remove the exhaust filter, unclip the exhaust filter cover [16] and remove the exhaust
filter pack. [17]
2. Wash the filter in hand warm water [18] and allow it to dry thoroughly before replacing
it in the cleaner. [19]
Remember: Do not use hot water or detergents. In the unlikely event of the filters
becoming damaged, fit a genuine Hoover replacement. Do not try and use the product
without a dust bag or filter fitted.
Cleaning the permanent cloth dust bag*:
To maintain optimum performance we recommend that you wash the permanent cloth
dust bag under hand warm water after every 5 full bags. Remove excess water and leave
to dry fully before replacing.
Removing a Blockage From The System
If the bag check indicator is red:
1. Check if the bag is full. If so refer to 'Replacing the dust bag'.
2
GB

Publicidad

loading