Publicidad
Idiomas disponibles
Idiomas disponibles
Step 12
Connect gas hose with burner. Ensure tight position.
Run a tightness/leak test.
The injector attached to this unit is not intended for removal. The injector is factory assembled. It is forbidden to change this device from one gas pressure to another
pressure. Do not connect gas cylinder directly to the unit without a regulator. The flexible hose should be approved according to EN16436:2014. The regulator must
comply with standard EN16129:2013, the outlet pressure of the regulator should correspond to the values on the nameplate. The replaced regulator must comply
with the specification listed in the technical data according to the national regulations.
GB
Step 13
Insert housing door J and close the door.
OPERATION
TO TURN ON THE HEATER
1. Turn ON the valve of the gas supply cylinder completely.
2. Push control knob in at the OFF position then turn counter-clockwise to Pilot position.
3. Push the control knob in, hold it for 30 seconds. Press the igniter button several times to light the burner. Release the control knob after the burner lights. The
flame is visible through the viewing hole. The control knob can be released after the flame lights. If the flame does not light or it goes out, REPEAT STEP 3.
4. Turn the control knob to the desired temperature position.
NOTES:
• If the pilot light has not ignited, turn heater control knob to OFF position, fully close gas valve, wait 5 minutes, then repeat steps 2–4 of the Lighting
Instructions.
• If the pilot light ignites but does not stay lit, turn heater control knob to OFF position, fully close gas valve, wait 5 minutes, then repeat steps 2–3.
Now, using a lighter, ignite the pilot light through the ignition hole on the emitter screen. Once the pilot light is lit, press control knob for 30 seconds.
5. After pressing the control knob for 30 seconds, turn control knob to Low. To increase the temperature, turn towards Hi.
WARNING!
• Check that no broken on the glass is found before operation.
• If a new gas bottle has been newly connected, let gas pipe air escape through ignition flame hole for at least one minute.
• When igniting the flame, ensure that the control knob is pressed the whole time while ignition button is pressed. The control knob can be released
once ignition flame is burning.
• You can observe and control the ignition flame through the little round window with sliding cover situated at the bottom of the radiation shade. The
ignition flame can also be lit with a match. Slide the sliding cover to the side in order to ignite the ignition flame with a match through the hole.
TO TURN OFF THE HEATER
1. Fully close gas valve on the gas cylinder.
2. Turn control knob clockwise to OFF position.
AFTER USE
CLEANING AND CARE
• Let the appliance cool down before cleaning.
• Wipe off powder coated surfaces with soft, moist rag. Do not clean heater with cleaners that are combustible or corrosive.
• Remove debris from the burner to keep it clean and safe for use.
• Cover the burner unit with the optional protective cover when the heater is not in use.
STORAGE
• Always close the gas value of the gas cylinder after use or in case of a disturbance.
• Remove the pressure regulator and the hose from the appliance.
• Check the tightness of the gas valve and other possible damage. If you suspect a damage, have the cylinder changed by
your gas dealer.
• Never store liquid gas cylinder in a sub-terrain, or at places without adequate air ventilation.
DURING PERIODS OF EXTENDED INACTIVITY OR WHEN TRANSPORTING
• Turn the control to "OFF" position.
• Disconnect LPG cylinder and move to a secure, well-ventilated location outdoors. DO NOT store in a location that will exceed 50 °C.
• Store heater upright in an area sheltered away from weather conditions (such as rain, sleet, hail, snow).
• Cover heater to protect exterior surfaces and to help prevent dust and debris collecting in air passages.
WARNING!
• DO NOT touch or move heater for at least 45 minutes after use.
• Allow all burner elements to cool before touching.
NOTES:
• In a salt-air environment (such as near the sea) corrosion occurs more quickly than normal.
• Frequently check for corroded areas and repair them promptly.
• Wait until heater is cooled down before covering.
TROUBLESHOOTING
Suspected malfunctions, errors or damage are often due to causes that the users can fix themselves. Therefore, check the appliance using the below table before
contacting a qualified specialist. In most cases the problem can be solved quickly.
WARNING!
Only perform the steps described within this instruction manual! All further inspection, maintenance and repair work must be performed by an authorised
service centre or a similarly qualified specialist!
Problem
Pilot will not light
Probable cause
• Gas valve is OFF
• Gas cylinder empty
• Opening blocked
• Air in supply system
• Loose connections
• Turn the gas valve ON
• Refill LPG tank
• Clean or replace opening
• Purge air from lines
• Check all fittings
10
Off: The heater stop working
Hi: Maximum temperature position
Lo: Minimum temperature position
Solution
Publicidad
