Bosch 0 601 9J2 204 Manual Original página 15

and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Charging the Battery
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The accessory no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Follow the instructions on correct disposal.
Removing the Battery
The battery (4) is equipped with two locking levels to pre-
vent the battery from falling out when pushing the battery re-
lease button (5) unintentionally. As long as the battery is in-
serted in the power tool, it is held in position by means of a
spring.
To remove the battery (4), press the release button (5) and
pull the battery out of the power tool. Do not use force to
do this.
Battery charge indicator
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Bosch Power Tools
Press the button for the battery charge indicator or
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Battery model GBA 18V...
LEDs
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Battery model ProCORE18V...
LEDs
5× continuous green light
4× continuous green light
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Changing the Tool
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Inserting the application tool (see figures A – B)
GDR 18V-200 / GDX 18V-200:
Pull the locking sleeve (2) forward, guide the application tool
(1) into the tool holder as far as it will go and release the
locking sleeve (2) to lock the application tool.
Impact-proof screwdriver bits (12) can be inserted using a
universal bit holder (11) with ball catch.
Inserting the application tool (see figures B – C)
GDX 18V-200 / GDS 18V-200:
When working with an application tool, pay attention
u
that the application tool is connected securely to the
tool holder. When the application tool is not securely
connected with the tool holder, it can come off during ap-
plication.
Slide the application tool (13) onto the square drive of the
tool holder (1).
English | 15
to
Capacity
60−100 %
30−60 %
5−30 %
0−5 %
Capacity
80−100 %
60−80 %
40−60 %
20−40 %
5−20 %
0−5 %
1 609 92A 8Y6 | (28.07.2023)