Noise/Vibration Information; Charging The Battery - Bosch EXACT 12V-6-670 Manual Original

16 | English
Industrial cordless screwdriver
EXACT
Permitted ambient temperature during op-
D)
eration and during storage
Compatible rechargeable batteries
Recommended rechargeable batteries for
maximum performance
Recommended chargers
A) Measured at 20–25 °C with rechargeable battery GBA 12V 6.0Ah.
B) Limited performance at speeds < 50 %)
C) Depends on battery in use
D) Limited performance at temperatures < 0 °C

Noise/vibration information

Noise emission values determined according to
EN 62841-2-2.
Typically, the A-weighted sound pressure level of the power
tool is less than 70 dB(A). The noise level when working can
exceed the volume stated. Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-2:
Impact tightening of fasteners of the maximum capacity of
2
the tool: a < 2.5 m/s , K = 1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Notes on Accuracy
The reduction in speed (especially below 50 %) can lower
the maximum torque. The increased speed when using
Power Boost may affect the accuracy and shut-off beha-
viour. The clutch may be released.
Machine capability tests are usually done at 600 rpm in ac-
cordance with VDI 2647.
1 609 92A 7DK | (24.11.2022)
°C
GBA 12V 2,0Ah
GBA 12V 3,0Ah
GBA 12V 6,0Ah
Changes to the speed and/or torque may affect the accur-
acy.
The machine capability must be checked with the relevant
setting.
Assembly
u
2

Charging the Battery

u
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
u
Follow the instructions on correct disposal.
Removing the battery (see figure A)
To remove the battery (7), press both release buttons (6)
and pull the battery downwards out of the power tool. Do
not use force to do this.
12V-6-670 12V-4-1100
–20 to +50 –20 to +50
GBA 12V... GBA 12V...
GBA 12V 2,0Ah
GBA 12V 3,0Ah
GBA 12V 6,0Ah
GAL 12... GAL 12...
GAX 18... GAX 18...
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
12V-2-670
–20 to +50
GBA 12V...
GBA 12V 2,0Ah
GBA 12V 3,0Ah
GBA 12V 6,0Ah
GAL 12...
GAX 18...
Bosch Power Tools