Black and Decker BL186 Manual De Instrucciones página 7

Make sure switch turns drill on and off.
u
Drilling in wood
Holes in wood can be made with the same twist drill bits used
for metal or with spade bits. These bits should be sharp and
should be pulled out frequently when drilling to clear chips
from the flutes.
Drilling in metal
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. The cutting
lubricants that work best are sulphurized cutting oil.
LED work light
When drill is activated by pulling the trigger switch (1), the
integrated LED work light (8)will automatically illuminate the
work area.
Note: The work light is for lighting the immediate work surface
and is not intended to be used as a flashlight.
Bit tip storage
A bit storage slot (9) is built into the base of the tool.
Troubleshooting
Problem Possible cause
Unit will not start. Battery pack not
installed properly.
Battery pack not
charged.
Unit starts immedi- The switch has
ately upon inserting been left in the "on"
battery position.
Battery pack will not Battery pack not
charge. inserted into charger.
Charger not plugged
in.
Surrounding air
temperature too hot or
too cold.
Unit shuts off Battery pack has
abruptly. reached its maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery pack it is
designed to shutoff
abruptly when the
charge is depleted
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
u
u
u
Protecting the environment
Z
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Possible solution
Technical data
Check battery pack
installation.
Check battery pack charg-
ing requirements
Voltage
The switch must be
moved to "off" to prevent
No-load speed
the tool from immediately
starting when battery is
Max. torque
inserted.
Chuck capacity
Insert battery pack into
charger until LED lights.
Max Drilling capacity
Plug charger into a work-
ing outlet. Steel/wood
Weight
Move charger and battery
pack to a surrounding air
temperature of above 40
Charger
degrees F (45ºC) or below
105 degrees F (+40.5ºC)
Input voltage
Allow battery pack to cool
down.
Output voltage
Current
Place on charger
and allow to charge.
Approx. charge time
Level of sound pressure according to EN 60745:
Sound pressure (L
Sound power (L
(Original instructions)
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
from the interior.
Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.
V
DC
Min
Nm
mm
mm
kg
V
AC
V
DC
mA
Hrs
Battery BL1518
Voltage V 18
AC
Capacity Ah 1.5
Type
Li-Ion
) 67 dB(A), uncertainty (K) 3 dB(A)
pA
) 78 dB(A), uncertainty (K) 3 dB(A)
WA
ENGLISH
BL186
18V
0-420 / 0-1650
-1
52
13
13/35
1.08 (1.46 with
battery)
905902** 906349**
100- 240 220 - 240
8 - 20 8 - 20
400 1000
4 - 10 1,5 - 4
BL2018 BL4018
18 18
2.0 4.0
Li-Ion Li-Ion
7