Whirlpool WFC 3C33 F X Guía Rápida página 2

EN
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature and
pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and sensor cali-
bration. The sensor calibration can increase program duration up to 20 min.
OPTIONS AND FUNCTIONS
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL). If an option is not compatible with the selected
program (see PROGRAMS TABLE), the corresponding LED flashes rapidly 3 times and beeps will sound. The option will not be enabled.
MULTIZONE - If there are not many dishes to be washed, a half load-
ing may be used in order to save water, electricity and detergent. By
default the appliance washes dishes in all racks.
KEYLOCK - A long press (for 3 seconds) of MULTIZONE button, will
activate the KEYLOCK function. To deactivate the KEYLOCK, long press again.
SANI RINSE - This option can be used to sanitize washed dishes.
It will increase final rinse temperature and add antibacterial wash to the
selected program. WARNING: the crockery and plates could be extremely
hot at the end of the cycle.
LOADING THE RACKS
CUTLERY RACK
(loading example for the cutlery
rack)
The third rack was designed to
house the cutlery.
CLEANING AND MAINTENANCE
CLEANING THE FILTER ASSEMBLY
A
In case you find foreign objects (such as broken glass, porcelain, bones, fruit seeds
etc.) please remove them carefully.
NEVER REMOVE the wash-cycle pump protection (black detail) (Fig 4).
TROUBLESHOOTING
PROBLEMS POSSIBLE CAUSES
No water in the water supply or the tap is closed.
The dishwasher does not
fill the water. Display shows:
The inlet hose is bent.
and F6, both On/Off
and START/Pause LEDs are
The sieve in the water inlet hose is clogged; it is
blinking rapidly.
necessary to clean it.
Dishwasher finishes the cycle
Drain hose positioned too low or siphoning into
prematurely.
home sewage system.
Display shows: F15 and both
On/Off and START/Pause
Air in water supply.
LEDs are blinking rapidly.
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
• Using QR code on your product.
• Visiting our website docs.whirlpool.eu and parts-selfservice.whirlpool.com
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting our After-sales
Service, please state the codes provided on your product's identification plate.
The model information can be retrieved using the QR-Code reported in the energy label.
The label also includes the model identifier that can be used to consult the portal of the registry at https://eprel.ec.europa.eu.
2
UPPER RACK
(loading example for the upper
rack)
Load delicate and light dish-
es: glasses, cups, saucers, low
salad bowls.
B
A
C
Please scan the QR code on your product in order to have more detailed information.
TABLET (Tab)- If you use powder or liquid detergent, this option
should be off.
DELAY -The start of the program may be delayed for a period of time
between 0:30 and 24 hours.
The DELAY function cannot be set once a wash cycle has been started.
NaturalDry is a convection drying system which automatically opens the
door during/after drying phase to ensure exceptional drying performance
every day. Door opens at the temperature that is safe to your kitchen fur-
niture, thus door will not be opened when the option of SANI RINSE is on.
Foldable
flaps with
adjustable
position
(loading example for the lower rack)
More information in the Daily Reference Guide on the website.
CLEANING THE SPRAY ARMS
To remove the upper spray arm,
turn the plastic locking ring in a
clockwise direction.
Please scan the QR code on your product in order to have more detailed information.
SOLUTIONS
Make sure there is water in the water supply or the tap running.
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwasher
and reboot.
After having carried out the verification and cleaning, turn off and turn on the dish-
washer and restart a new program.
Check if end of drain hose is placed at correct height (see INSTALLATION).Check for
siphoning into home sewage system, install air admittance valve if necessary.
Check water supply for leaks or other issues letting air inside.
Quick Guide
CAPACITY: 14 standard place-settings
LOWER RACK
For pots, lids, plates, salad bowls, cutlery
etc. Large plates and lids should ideally
be placed at the sides to avoid interfer-
ences with the spray arm.
The lower rack has tip-up supports
which can be used in a vertical position
when arranging plates or in a horizontal
position (lower) to load pans and salad
bowls easily.
The lower spray arm may
be removed by pulling it
upwards.
:
IEC 436