Whirlpool W11462846B Manual De Instrucciones

DRAIN REQUIREMENTS
A new drain hose is supplied with your dishwasher. If drain
n
hose is not long enough, use a new drain hose with a
maximum length of 12 ft (3.7 m) that meets all current AHAM/
IAPMO test standards, is resistant to heat and detergent, and
fits the 1" (25 mm) drain connector of the dishwasher. See
the "Tools and Parts" section at the front of the guide for part
details and orders.
Make sure to connect drain hose to waste tee or disposer
n
inlet above drain trap in house plumbing and 20" (508 mm)
minimum above the floor. It is recommended that the drain
hose either be looped up and securely fastened to the
underside of the counter or be connected to an air gap.
Make sure to use an air gap if the drain hose is connected to
n
house plumbing lower than 20" (508 mm) above subfloor or
floor.
Use of air gap
Air gap
If required, the air gap should be installed in accordance with
n
the air gap installation instructions. When you are connecting
the air gap, a rubber hose (not provided) will be needed to
connect to the waste tee or disposer inlet.
Use 1/2" (13 mm) minimum I.D. drain line fittings.
n
WATER SUPPLY REQUIREMENTS
This dishwasher has a water heating feature and also requires
n
a connection to a hot water supply line.
A hot water line with 20 psi to 120 psi (138 kPa to 862 kPa)
n
water pressure can be verified by a licensed plumber.
120°F (49°C) water at dishwasher.
n
3/8" (9.5 mm) O.D. copper tubing with compression fitting or
n
flexible braided water supply line.
NOTE: 1/2" (13 mm) minimum plastic tubing is not
recommended.
A 90° elbow with 3/4" (19 mm) hose connection with rubber
n
washer.
Do not solder within 6" (152 mm) of the water inlet valve.
n
If installed in new construction, make sure the house water
n
supply lines have been flushed prior to connecting the
dishwasher to remove any debris that may exist in the supply
line.
NOTE: If replacing an existing dishwasher, it is recommended
to install a new water line and drain hose (supplied) with the
new dishwasher.
Because Whirlpool Corporation policy includes a continuous commitment to
improve our products, we reserve the right to change materials and specifications
without notice.
W11462846B
03-Jun-2020 12:49:43 EDT | RELEASED
Undercounter Dishwasher
ELECTRICAL REQUIREMENTS
You Must Have:
120 V, 60 Hz, AC only, 15 A or 20 A, fused electrical supply
n
Copper wire only
n
A maximum of 2 field wiring supply conductors (12 AWG
n
largest size) plus 1 grounding conductor are permitted in the
terminal box.
We Recommend:
A time-delay fuse or circuit breaker.
n
A separate circuit
n
If connecting dishwasher with a power supply cord:
Use UL Listed power cord kit marked for use
n
with dishwasher.
Plug into a grounded 3 prong outlet.
n
Outlet must meet all local codes and
ordinances.
If connecting dishwasher with direct wiring:
Use flexible, armored, or nonmetallic
n
sheathed copper wire with grounding wire
that meets the wiring requirements for your
home and local codes and ordinances.
Use a UL Listed/CSA Approved metallic
n
strain relief.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
In some European factories the letter "W" of the part code mentioned herein will be automatically
replaced by the number "4000" (e.g. "W12345678" becomes "400012345678")
1