Bosch AHS 480-24T Manual Original página 11

OBJ_BUCH-2115-001.book Page 11 Friday, December 6, 2013 11:19 AM
Electrical Safety
 Warning! Switch off, remove plug from mains before
adjusting, cleaning or if cable is cut, damaged or entan-
gled.
 The blades continue to move for a few seconds after
the hedgecutter is switched off. Caution! Do not touch
the moving blades.
Your machine is double insulated for safety and requires no
earth connection. The operating voltage is 230 V AC, 50 Hz
(for non-EU countries 220 V, 240 V as applicable). Only use
approved extension cables. Contact your Bosch Service Cen-
tre for details.
Extension cords/leads should only be used if they comply
with H05VV-F or H05RN-F types.
It is recommended for increased electrical safety to use a Residu-
al Current Device (RCD) with a tripping current of not more than
30 mA. Always check your RCD every time you use it.
For products not sold in GB:
WARNING: For your safety, it is required that the plug at-
tached to the machine is connected with the extension cord.
The coupling of the extension cord must be protected against
splash water, be made of rubber or coated with rubber. The
extension cord must be used with a cable strain relief.
The connection lead must be inspected for signs of damage at
regular intervals and may only be used if in perfect condition.
If the supply cord is damaged, it must be replaced by a Bosch
Service Centre.
Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains sock-
et elsewhere.
Products sold in AUS and NZ only: Use a residual current de-
vice (RCD) with a rated residual current of 30 mA or less.
Maintenance
 Examine the machine and replace worn or damaged parts
for safety.
Technical Data
Hedgecutter
Article number
Rated power input
No-load stroke rate
Tooth opening
Cutting length
Weight according to EPTA-Procedure
01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your garden product. The trade names of the individual garden products may vary.
Bosch Power Tools
 Always lubricate the cutting blade with protective spray
before storage.
 Keep all nuts, bolts and screws tight to be sure that the ma-
chine is in safe working condition.
 Ensure replacement parts fitted are Bosch approved.
 Always lubricate the cutting blade with protective
spray before use.
Symbols
The following symbols are important for reading and under-
standing the operating instructions. Please take note of the
symbols and their meaning. The correct interpretation of the
symbols will help you to use the garden product in a better
and safer manner.
Symbol
Intended Use
The machine is intended for cutting and trimming hedges and
bushes in domestic use.
AHS 400-24T AHS 480-24T
3 600 ... H48 0..
W 550
-1
min 1400
mm 24
mm 400
kg 3.9
/II
English | 11
Meaning
Reaction direction
Movement direction
Wear protective gloves
Weight
Switching On
Switching Off
Permitted action
Prohibited action
Accessories/Spare Parts
AHS 550-24ST AHS 600-24ST
H48 1.. H48 2..
550 600
1400 1400
24 24
480 550
4.0 4.1
/II /II
F 016 L81 083 | (6.12.13)
H48 3..
600
1400
24
600
4.2
/II