Publicidad
Idiomas disponibles
Idiomas disponibles
CAUTION: Always use the correct screws for the
attaching the charger to the D
mount. Using the wrong screws will reduce the holding
force required for proper installation possibly resulting
in personal injury or property damage.
Mounting D
WALT Battery Chargers
e
DCB115, DCB112, DCB1104, DCB118,
DCB1106, DCB1112 (Fig. A—F)
Required Tools and hardware
‑
One M4 x 4 nail screw
‑
Two ST5 x 12 screws
Screwdriver
‑
Mounting
1. Place the D
WALT battery charger
e
Check the span dimension
bottom housing as shown in Fig. B.
2. According to the span dimension, screw one M4 x 4 nail
screw
2
into the corresponding screw hole
tighten it to 13 in-lb. Do not overtighten.
nOTE: The screw hole
rail mount is for the following chargers; DCB115, DCB112,
and DCB1104 with a 4.5" (114 mm) keyhole span.
nOTE: The screw hole
charger rail mount is for the following chargers; DCB118
and DCB1106 with a 5.25" (133 mm) keyhole span.
nOTE: The screw hole
charger rail mount is for the charger DCB1112 with 6-3/8"
(162 mm) keyhole span.
3. Slide the charger downward and engage the
keyholes
10
with two nail hooks
4. Insert the plastic plug
screw hole
14
of the charger from the rear of the
D
WALT battery charger rail mount.
e
5. The triangle marking
the slot
15
when the plastic plug
screw hole
14
as shown in Fig. E and Fig. F.
nOTE: The screw hole
charger rail mount is for the following chargers; DCB115,
DCB112, and DCB1104.
nOTE: The screw hole
charger rail mount is for the following chargers; DCB118
and DCB1106.
nOTE: The screw hole
charger rail mount is for the charger DCB1112.
6. Screw one ST5 x 12 screw
shown in Fig. E.
Mounting D
WALT DCB1102 Battery
e
Charger (Fig. G—I)
Required Tools and hardware
‑
Three M4 x 4 Nail Screws
‑
Two ST5 x 12 Screws
‑
Screwdriver
WALT charger rail
e
2
3
8
charging side down.
9
of two keyholes
11
11
on the D
WALT battery charger
e
12
on the D
WALT battery
e
13
on the D
WALT battery
e
5
as shown in Fig. D.
6
into the corresponded bottom
7
of the plastic plug
6
aligns with
6
is inserted into the
14
on the D
WALT battery
e
18
on the D
WALT battery
e
19
on the D
WALT battery
e
into each plastic plug
3
2
3
Mounting
1. Screw one M4 x 4 nail screw
20
as shown in Fig. G and tighten it to 13 in-lb. Do not
overtighten.
2. Slide the charger downward and engage the
keyholes
3. Insert the plastic plug
from the rear of the D
4. The triangle marking
the slot
hole
21
5. Screw one ST5 x 12 screw
shown in Fig. I.
MAINTENANCE
10
on the
Your D
WALT product has been designed to operate over
e
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
care and regular cleaning.
and
Cleaning
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never immerse any part of the rail
into a liquid.
Accessories
WARNING: Since accessories, other than those offered
by D
of such accessories with this product could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
(1‑800‑433‑9258) or visit our website: www.dewalt.com
Repairs
The DWST82821 is not serviceable.
Register Online
Thank you for your purchase. Register your product now for:
as
6
• WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of an
insurance loss, such as fire, flood or theft, your registration
of ownership will serve as your proof of purchase.
• FOR YOUR sAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification
is required under the Federal Consumer Safety Act.
• Register online at www.dewalt.com.
2
into each screw hole
10
with two nail hooks
6
into the corresponding hole
WALT battery charger rail mount.
e
7
of the plastic plug
15
when the plastic plug
as shown in Fig. F.
3
into each plastic plug
WALT, have not been tested with this product, use
e
WALT call 1‑800‑4‑D
e
English
5
as shown in Fig. H.
21
6
aligns with
6
is inserted into the
6
as
WALT recommended
e
WALT
e
5
Publicidad
