Descargar Imprimir esta página

Hama 00221062 Instrucciones De Uso página 7

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 17
5.4 Overview of compatible remote controls
Due to the large number of different remote controls, we can only
provide a limited number in the code list. If the button diagram and
housing shape of your original remote control match one of the models
shown, it is compatible (page 47).
5.5 Restoring factory settings
Press and hold the [RETURN] and [0] buttons simultaneously for approx.
5 sec. until the status LED ashes three times and then goes out. The
remote control is now successfully reset to the factory setting.
Note
All taught-in or copied buttons as well as all settings of the remote
control will be deleted.
6. Learning function
This remote control is equipped with a learning function. This allows
you to transfer functions from your original remote control to this
remote control.
6.1 Before you start the learning function
• Make sure that all batteries used in both remote controls are in
perfect condition. Change them if necessary.
• Place your original remote control and the remote control next to
each other so that the infrared diodes of the remote controls are
directly opposite each other.
• If necessary, correct the height of both remote controls to achieve
optimal alignment.
• The distance between the two remote controls should be approx.
3 cm.
HAMA
ORIGINAL
ca. 3 cm
Note
• Do not move the remote controls during the learning process.
• Make sure that the room lighting is not uorescent tubes or
energy-saving lamps, as these could cause interference and thus
hinder the learning process.
• The distance between the two remote controls and the nearest
light source should be at least 1 metre.
• The learning process is terminated without saving if no button is
pressed or no signal is received for 15 sec. while learning mode
is activated.
• In learning mode, each button can only be assigned one function.
A new function overwrites the function previously taught on this
button.
3
6.2 Activating the learning mode
1.
Press and hold the [MUTE] and [VOL+] buttons simultaneously for
approx. 5 sec. until the status LED lights up continuously.
5
2.
Enter the code [9] [8] [0], the status LED ashes 2 times and then
lights up permanently.
3.
The remote control is now in learning mode.
6.3 Transferring the button function
1.
Press the button on the original remote control whose function
you want to transfer. To con rm that the command has been
received, the status LED of the replacement remote control
ashes.
2.
Now press the button on the replacement remote control to
which the function is to be transferred.
3.
The function LED of the replacement remote control ashes 3
times for con rmation and then lights up permanently again. The
new function is now saved.
4.
To transfer the functions of additional buttons, repeat these steps.
5.
Press the [MUTE] and [VOL-] buttons to save all taught-in
functions and exit the learning mode.
Note
When changing the batteries of the remote control, the functions of
the taught-in buttons are retained.
6.4 Deleting taught functions
6.4.1 Deleting a taught function
1.
Press and hold the [MUTE] and [VOL+] buttons simultaneously for
approx. 5 sec. until the status LED lights up continuously.
5
2.
Enter the code [9] [8] [1], the status LED ashes 2 times and then
lights up permanently again.
3.
Press the button whose function you wish to delete. The status
LED ashes 3 times and the desired function is deleted.
6.4.2 Deleting all taught functions
1.
Press and hold the [MUTE] and [VOL+] buttons simultaneously for
approx. 5 sec. until the status LED lights up continuously.
5
2.
Enter the code [9] [8] [2], the status LED ashes 2 times and then
lights up permanently again.
3.
Press the [OK] button, the status LED ashes 3 times and all
taught-in functions are deleted.

Publicidad

loading