RIDGID R9600VN Manual Del Operador página 6

OPERATION
WARNING:
Do not allow familiarity with products to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict severe injury.
WARNING:
Always remove battery pack from the product when
you are assembling parts, making adjustments,
cleaning, or when not in use. Removing battery
pack will prevent accidental starting that could
cause serious personal injury.
R86008/R86008VN DRILL/DRIVER AND R86034/R86034VN IMPACT DRIVER
APPLICATIONS
You may use this product for the purposes listed below:
R86008/R86008VN
Drilling and driving screws in all types of wood products
(lumber, plywood, paneling, composition board, and hard
board), ceramics, plastics, fiberglass, laminates, metals;
Driving screws into wood and drywall with screwdriver bits
R86034/R86034VN
Driving and removing screws/lag bolts; tightening screws,
nuts, and bolts
INSTALLING BELT HOOK
See Figure 3, page 10 (R86008/R86008VN).
See Figure 1, page 12 (R86034/R86034VN).
The belt hook may be used on either side of the tool base.
 Align hole in belt hook with hole in tool's base.
 Install screw to secure belt hook in place.
VARIABLE SPEED SWITCH TRIGGER
See Figure 4, page 11 (R86008/R86008VN).
See Figure 2, page 12 (R86034/R86034VN).
The variable speed switch trigger delivers higher speed with
increased trigger pressure and lower speed with decreased
trigger pressure.
To turn the tool ON, depress the switch trigger. To turn it
OFF, release the switch trigger and allow the chuck to come
to a complete stop.
NOTE: A whistling or ringing noise coming from the switch
during use is a normal part of the switch function.
NOTE: Operating at low speeds under constant usage may
cause the tool to become overheated. If this occurs, cool
the tool by running it without a load and at full speed.
DIRECTION OF ROTATION SELECTOR
(FORWARD/REVERSE/CENTER LOCK)
See Figure 4, page 11 (R86008/R86008VN).
See Figure 2, page 12 (R86034/R86034VN).
Set the direction of rotation selector in the OFF (center lock)
position to lock the switch trigger and help prevent accidental
starting when not in use.
WARNING:
Always wear eye protection with side shields
marked to comply with ANSI Z87.1. Failure to do
so could result in objects being thrown into your
eyes, resulting in possible serious injury.
Position the direction of rotation selector to the left of the
switch trigger for forward drilling. Position the selector to the
right of the switch trigger to reverse the direction.
NOTE: The tool will not run unless the direction of rotation
selector is pushed fully to the left or right.
NOTICE:
To prevent gear damage, always allow the tool
to come to a complete stop before changing the
direction of rotation.
WARNING:
Battery tools are always in operating condition.
Lock the switch when not in use or carrying at your
side, when installing or removing the battery pack,
and when installing or removing bits.
INSTALLING/REMOVING BATTERY PACK
See Figure 5, page 11 (R86008/R86008VN).
See Figure 3, page 12 (R86034/R86034VN).
 Lock the switch trigger.
 Insert the battery pack into the tool.
 Make sure the latches on each side of the battery pack
snap in place and that battery pack is secured in the
product before beginning operation.
 Depress the latches to remove the battery pack.
For complete charging instructions, see the operator's manu-
als for your battery pack and charger.
LED GRIP LIGHT
See Figure 6, page 11 (R86008/R86008VN).
See Figure 5, page 12 (R86034/R86034VN).
The LED light illuminates when either the switch trigger
or LED grip light switch is depressed and when there is
a charged battery in the tool. If the tool is not in use, the
time-out feature will cause the light to start fading and then
shut off.
6 - English