Publicidad
Idiomas disponibles
Idiomas disponibles
1. Mark the location of the charging station screw holes
on the wall at a height that allows the unit to hang
without hitting the floor and within reach of an electrical
outlet for charging the vacuum while it is on the
charging station
22
2. Fix the charging station
appropriate screws and plugs for the type of wall, and
weight of the appliance.
3. Slide the circular magnetic charging contact
the charging station
push the release button
magnetic charging contact
positon until the release button pushes back into place.
Ensure it is locked into position before proceeding.
nOTE: To remove the circular magnetic charging
contact
25
from the charging station
release button
on the charging station
26
slide the circular magnetic charging contact
away from the charging station.
4. Plug the charger into an appropriate outlet.
5. Place the vacuum storage slot
the unit
28
onto the vacuum storage hook
the charging station
22
the unit
28
is secure on the vacuum storage hook
before proceeding.
6. The blue LED
27
on the battery charge indicator
flash indicating that the battery is being charged.
7. The blue LEDs will illuminate in segments, displaying the
state of charge in the battery
8. The completion of charge is indicated by the blue
LEDs
27
turning off.
9. The unit is fully charged and may be used at this time or
left on the charger.
ASSEMBLY AND ADJUSTMENTS
WARNING:
serious personal injury, turn unit off before
making any adjustments or removing/installing
attachments or accessories. An accidental start‑up
can cause injury.
Assembly (Fig. F)
WARNING:
unit with the rear of the vacuum facing a wall so that
any inadvertent fall of the unit would contact a wall
and not people or pets.
1. Align the top of the extension tube
vacuum inlet
7
as shown in Fig. F.
2. Push the extension tube
locks into position.
3. Align the bottom of the extension tube
head
14
as shown in Fig. F.
4. Push the bottom of the extension tube
head
14
so it locks into position.
.
22
to the wall using
25
22
as shown in Fig C. To do this
26
down to allow the circular
25
to slide down into
22
press the
22
38
at the rear of
29
as shown in Fig E. Ensure
To reduce the risk of
When not in use position the
8
with the
8
onto the vacuum inlet
8
with the floor
8
onto the floor
5. To remove an accessory, press the extension pole release
button
of the extension tube and gently pull the connected
accessory off.
OPERATION
WARNING:
serious personal injury, turn unit off before
into
making any adjustments or removing/installing
attachments or accessories. An accidental start‑up
can cause injury.
State of Charge Indicator
This appliance includes a state of charge indicator which
consists of three blue LED lights that indicate the level of
charge remaining in the battery. This feature is only activated
and
when the vacuum is powered on or during a charge cycle.
up and
25
The state of charge indicator is an indication of approximate
levels of charge remaining in the battery pack according to
the following indicators:
The LED battery indicator displays the remaining charge
of
and warns you when the battery is low. The final LED will
flash continuously when there is approximately one minute
29
of runtime remaining. All LEDs will flash when the unit
is discharged.
4
will
nOTE: The state of charge indicator is only an indication
of the charge left on the battery. It does not indicate tool
functionality and is subject to variation based on product
components, temperature and end-user application.
Use (Fig. G)
This vacuum can be used in one of four ways.
‑
With the extension tube
‑
With the floor head
With the extension tube
‑
16
‑
With an accesssory tool
Switching ON and OFF (Fig. H)
1. To switch ON, push the ON/OFF button
nOTE: The state of charge indicator LEDs will illuminate
while the vacuum is ON.
2. Press the hard floor button
tile floors.
nOTE: The rotarty brushes of the floor head
powered pet head
carpet modes.
3. Press the carpet button
cleaning carpeted flooring.
4. To switch OFF, press the ON/OFF button
7
so it
5. Return the product to the charger immediately after use
so that it will be fully charged and ready for the next use.
nOTE: Ensure that the product is fully engaged with the
charger plug.
9
located on the vacuum inlet or the bottom
To reduce the risk of
8
14
.
8
,
17
,
19
,
20
.
16
,
2
for cleaning wood, vinyl or
20
will turn on in both hard floor and
3
for increased suction power for
English
and the floor head
14
.
and an accesssory tool
17
,
19
,
20
.
1
.
14
or the
1
a second time.
9
Publicidad
