Bosch GLI 18V-1900 Professional Manual Original página 10

10 | English
Cordless worklight
Recommended chargers
A) Limited performance at temperatures < 0 °C
The colour rendition of illuminated objects can be distorted.
Assembly
Battery Charging (Accessory)
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
cordless worklight.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". A protective circuit
switches the cordless worklight off when the battery is
drained.
Do not continue to press the On/Off switch after the
u
worklight has been automatically switched off. The
battery can be damaged. Ensure that the battery is
charged and that the worklight has cooled before switch-
ing on the worklight again.
To remove the battery (3), press the release button (2) and
pull the battery out of the cordless worklight. Do not use
force to do this.
Follow the instructions on correct disposal.
Operation
Starting Operation
Inserting the battery
Insert the charged battery (3) into lamp head (4) until it can
be felt to engage and faces flush against the lamp head.
Setting up
Carefully fold out the stand (5) and place the cordless work-
light on the floor. Make sure it is secure.
Fastening to the Tripod
You can use the tripod mount (7) to screw the cordless
worklight onto a tripod.
Attach the cordless worklight firmly to the tripod. Ensure the
cordless worklight cannot come loose and/or fall over.
Ensure that the tripod has a firm footing.
Swivelling the Lamp Head (see figure A)
The lamp head (4) is attached to the carrying handle (8).
The lamp head can be set to five different positions using the
carrying handle.
1 609 92A 7NS | (21.04.2022)
Switching On and Off
GLI 18V-1900
To switch on the cordless worklight, press the on/off
GAL 18...
switch (1).
GAX 18...
To switch off the cordless worklight, press the on/off
GAL 36...
switch (1) again.
Adjusting the Brightness
Press the on/off switch (1) briefly to switch on the cordless
worklight with maximum brightness. To adjust the bright-
ness in two stages, hold down the on/off switch (1) until the
required brightness is reached.
Temperature Dependent Overload Protection
If the permissible operating temperature is exceeded, the
cordless worklight switches off. Let the cordless worklight
cool down and then switch the cordless worklight back on.
Battery charge indicator
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator or
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Battery model GBA 18V...
LEDs
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Battery model ProCORE18V...
LEDs
5× continuous green light
4× continuous green light
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Practical Advice
Shortly before the cordless worklight switches off because
of an empty battery, it will flash three times and shine with
reduced brightness.
to
Capacity
60−100 %
30−60 %
5−30 %
0−5 %
Capacity
80−100 %
60−80 %
40−60 %
20−40 %
5−20 %
0−5 %
Bosch Power Tools