Publicidad
Idiomas disponibles
Idiomas disponibles
OBJ_BUCH-3506-002.book Page 30 Tuesday, April 17, 2018 2:51 PM
30 | English
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for cutting, roughing and brushing of
metal and stone materials without the use of water.
For cutting with bonded abrasives, a special cutting guard
(accessory) must be used.
When cutting in stone, provide for sufficient dust extraction.
With approved sanding tools, the machine can be used for
sanding with sanding discs.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
Technical Data
Angle Grinder
Article number
Rated power input
Output power
Rated speed
Grinding disc diameter, max.
Thread of grinder spindle
Thread length (max.) of grinder spindle
Weight according to EPTA-Procedure 01:2014
– with vibration-damping auxiliary handle
– with standard-auxiliary handle
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise levels of the product are:
Sound pressure level 91 dB(A); Sound power level
102 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3:
2
Surface grinding: a
= 5.4 m/s
, K=1.5 m/s
h
2
Disk sanding: a
=3.4 m/s
, K=1.5 m/s
h
1 609 92A 3YH | (17.4.18)
1 Spindle lock button
2 On/Off switch
3 Lock-off button for On/Off switch
4 Combination wrench for grinding spindle M14
5 Auxiliary handle (insulated gripping surface)
6 Grinder spindle
7 Protection guard for grinding
8 Mounting flange
9 Grinding wheel*
10 Clamping nut
11 Carbide grinding head*
12 Protection guard for cutting*
13 Cutting disc*
14 Hand guard*
15 Rubber sanding plate*
16 Sanding sheet*
17 Round nut*
18 Cup brush*
19 Handle (insulated gripping surface)
20 Release lever for protection guard
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
GWS 9-115 P GWS 9-115 P GWS 9-125 P GWS 9-125 P
3 601 C96 5.. 3 601 C96 5.. 3 601 C96 5.. 3 601 C96 5..
W
900
W
450
-1
min
11000
mm
115
M 14
mm
kg
2.0
kg
1.9
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
2
An estimation of the level of exposure to vibration should also
,
2
take into account the times when the tool is switched off or
.
900
900
450
450
11000
11000
115
125
5/8"
M 14
22
22
22
2.0
2.0
1.9
1.9
/II
/II
/II
900
450
11000
125
5/8"
22
2.0
1.9
/II
Bosch Power Tools
Publicidad
