Publicidad
Idiomas disponibles
Idiomas disponibles
RIP & CIRCLE CUTTING
Ripping and circle cutting without a pencil line are easily done with the a rip fence and
circle guide (available at extra cost).
When ripping, slide the rip fence under the screw from either side of the saw. Set the
cross bar at desired distance from blade and tighten screw. For ripping, the cross bar
should be down and against the straight edge of the workpiece.
When circle cutting, adjust rip fence so that distance from blade to hole in cross bar
is at the desired radius and tighten screw. Place saw so that hole in cross bar is over
center of circle to be cut (drill hole for blade or cut inward from edge of material to get
blade into position). When saw is properly positioned, drive a small nail through hole
in cross bar. Using rip fence as a pivot arm, begin cutting circle. For circle cutting, the
cross bar should be up.
MAINTENANCE
CAUTION:
metallic parts of the tool. Use only mild soap and damp cloth to clean the tool. Never let
any liquid get inside the tool; never immerse any part of the tool into a liquid.
The RBRC™ Seal
The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the
Li-Ion battery (or battery pack) indicates that the costs to recycle the battery (or
battery pack) at the end of its useful life have already been paid by PORTER-
CABLE. RBRC™ in cooperation with PORTER-CABLE and other battery
users, has established programs in the United States to facilitate the collection
of spent Li-Ion batteries. Help protect our environment and conserve natural resources
by returning the spent Li-Ion battery to an authorized PORTER-CABLE service center or
to your local retailer for recycling. You may also contact your local recycling center for
information on where to drop off the spent battery.
Rechargeable Battery Recycling Corporation.
REPLACEMENT PARTS
Use only identical replacement parts. For a parts list or to order parts, visit our service website
at www.portercable.com. You can also order parts from your nearest PORTER-CABLE Factory
Service Center or PORTER-CABLE Authorized Warranty Service Center. Or, you can call our
Customer Care Center at (888) 848-5175.
SERVICE AND REPAIRS
All quality tools will eventually require servicing and/or replacement of parts. For
information about PORTER-CABLE, its factory service centers or authorized warranty
service centers, visit our website at www.portercable.com or call our Customer Care Center
at (888) 848-5175. All repairs made by our service centers are fully guaranteed against
defective material and workmanship. We cannot guarantee repairs made or attempted by
others.
You can also write to us for information at PORTER-CABLE, 4825 Highway 45 North,
Jackson, Tennessee 38305, (888) 848-5175 - Attention: Product Service. Be sure to
include all of the information shown on the nameplate of your tool (model number, type,
serial number, etc.).
ACCESSORIES
WARNING:
have not been tested with this product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only PORTER-CABLE recommended
accessories should be used with this product.
A complete line of accessories is available from your PORTER-CABLE Factory Service
Center or a PORTER-CABLE Authorized Warranty Service Center. Please visit our
Web Site www.portercable.com for a catalog or for the name of your nearest supplier.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
Never use solvents or other harsh chemicals for cleaning the non-
Since accessories, other than those offered by PORTER-CABLE,
RBRC™ is a registered trademark of the
10
Publicidad
