Publicidad
Idiomas disponibles
Idiomas disponibles
Dear record lover:
Please read these instructions carefully before
you set up and operate your new automatic
turntable. By doing so, you will avoid faulty
operation or possible damage due to mistakes
in installation.
Move page 2 outward.
Unpacking
Remove all parts used for packing, including
the wedges between
the chassis and the
platter. Notice whether a cartridge is moun
ted in the tonearm
head and remove the
protective cap that may be over the stylus
Instructions for mounting the cartridge as
well as technical data on factory-mounted
cartridges are found on a separate sheet
enclosed with this instruction manual.
Set
stylus pressure dial to O. If the tonearm does
not float freely in a horizontal
position
adjust balance as described on page 10, Now
dial stylus pressure to that recommended
for your cartridge:
Note: After initial installation and after every
transport,
allow the automatic mechanis:
10 adjust itself by operating the unit through
one change cycle with the tonearm locked
on
its rest [move
the opera
'start")
lever to
Installation
The installation instruct
the phonagraph is boug!
If your system requires a preamplifier, make
the necessary connections to the Dual 1216
The following instructions are exceedingly
simple
Press the chassis mounting screws towa
the edge of the chassis with your thumbs
and set the chassis down on the base cut
out so that the three spring cups slip into
their holes (A). Then turn the mounting
screws clockwise, The chassis is now spring
(B)
Turn them
further until
the chassis is s
cured tightly to the mounting board (C
To prepare the
unit for use again, turn the
two screws clockwise until they slide down
about 3/4",
then continue to turn
in the
same direction until they are tight.
Power-line connections
For units already
installed i n console or
compact
systems, consult the instructions for the system
The unit can be used with 50 or 60 Hz
alternating current, at
110 or 220 volts. It ıs
normally pre-set for
volts, 50 Hz
The voltage for which the unit has been
preset can be read on the voltage selector
The frequency will be found on the name.
plate.
Both are found o
of the chassis
the underside
In units without
a voltage selector,
the
correct operating
voltage must be set by
inserting the motor power
cable into the
appropriate terminals according to the dra
wing in the power switch cover
Fig.3
The power switch is designed so that pre
amplifiers or poweramplifiers can be swit
ched on or off automatically as the unit is
turned on or off
The
load on the power switch must not
exceed 400 VA (Volt-amperes),
It is gener
ally used only with all-transistor amplifiers,
which have no warm-up delay.
The connection is made
vided on the plug pol
switch
contacts pro-
ion
of the power
case,
the line cord is to be fitted
with AMP plugs as follows
For 5-contact connector B.N
AMP No. 160 565/1 (Fig.
For 4-contact
connector B,No, 209 458
AMP No, 42 859/1 (Fig. 3)
213982,
Connection to amplifier
In combination units, e.g., hifi stereograms
the connection of the turntable to the amplifier
is done already
The unit can be fitted with DIN 41524
miniature connectors (Fig. 4) or with phono
(RCA) plugs (Fig. 5)
= left channel
= right channel
If your amplifier
type
of
s fitted with a different
connector,
use suitable adapters,
available
from audio dealers.
è
l
tet chan
an came
Fig. 5
If the unit is to be connected to a power
transformerless ("ac-de") radio, amplifier or
other equipment, a suitable ground connec
tion must be made to prevent a possible
shock hazard, A contact
is available for
this purpose on the power connector (Figs.
2 and 3)
Publicidad
