Publicidad
Idiomas disponibles
Idiomas disponibles
the scissors in the direction of growth from the bottom
up. If you cut downwards, the narrower branches may
move outwards, creating gaps or so-called holes.
- You can cut the upper edge according to your taste
in a straight shape, in the shape of a roof or in a
round shape.
- Cut the young plants to the desired shape. The main
plants should remain undamaged until the hedge
reaches the planned height. All other shoots can be
cut in half.
Caring for free-growing shrubs
Free-growing shrubs are not pruned into any shape,
but must be regularly maintained to prevent them
from growing very tall.
Time to cut
Deciduous hedges - in June and August.
Hedges of conifers - April and April.
Evergreen fences of conifers - from May.
Problem solving.
1. The switch is pressed, but the tool does not work:
The tool needs a sufficiently charged battery to work.
If you don't use the tool for a long time, the battery
will run out. Try charging the battery. Make sure the
battery is placed correctly in the charger. The adapter
heats up during charging, which is normal.
2. Battery leaks: At extreme temperatures, or under
extreme stress, a small leak may occur. If the liquid
comes in contact with it, immediately wash it off your
skin or clothing with soap and water.
3. The battery does not charge and the light on the
charger does not light: If the battery does not charge,
check if the charger is inserted correctly and make
sure the light is on.
4. The tool will become warm during prolonged use:
Under normal load, the body, switch and battery will
become warm because the energy consumed produ-
ces heat. It is normal. Simply let the tool cool down for
a few minutes.
5. The battery gets hot during use: The energy drawn
from the battery generates heat. It does not damage
the battery, the heat from the power draw is normal.
6. The battery becomes warm during charging: This
is normal and is due to the chemical reactions taking
place inside the battery during the charging process.
8. During charging, the charger will heat up: This is
normal and it results from the voltage reduction from
230V to 7.2V.
CLEANING AND MAINTENANCE
! Always remove the battery from the tool before
cleaning and maintenance.
Your tool needs no additional lubrication or mainte-
nance. There are no repairable parts in it.
Never use water or chemical cleaners to clean your
tools. Wipe it with a dry cloth.
Keep the motor fan openings clean.
Never clean any part of the tool with a hard, sharp or
rough object.
Storage when not in use for a long time
Do not store the tool where it is
high temperature.
If possible, store tools in a place with constant tempe-
rature and humidity.
SPECIFICATIONS
Working voltage 7.2V DC
Speed without load 1100 min-1
working time: 35-45 minutes
Soft grip
laser cutting
Lawn mower blade width: 90 mm
Cutting length of the bush trimmer: 170 mm
Distance between brush cutter teeth: 8 mm
with tool-free blade change with integrated knife set
structure
with power indication and charging lights
with built-in battery and charging port
Battery - LI-ION 7.2V/1500 mAh
Charging unit
Prim. 230V~50Hz
Sec. 9V, 400mA Weight 0.5 kg
Sound pressure level measured according to EN
60745:
LpA (sound pressure) 92 dB (A) KpA=3
LWA (acoustic power) 100 dB (A) KwA=3
Take appropriate measures to protect your hearing!
Use hearing protection whenever the sound pressure
level exceeds 80 dB (A).
Weighted effective acceleration value according to
EN 60745: 3.091 m/s2 K=1.5
Caution: The vibration level may vary during power
tool operation from the declared value depending on
the way the power tool is used and depending on
the following conditions: Method of power tool use
and type of material being cut or drilled, conditions
of the power tool and method of its maintenance,
appropriateness of the used accessories and ensu-
ring its sharpness and good conditions, the strength
of handle gripping, use of anti-vibration equipment,
suitability of the power tool for the purpose for which
it has been designed and compliance with workflows
according to manufacturer's instructions.
If this power tool is used in an inappropriate manner,
a hand/shoulder vibration syndrome may appear.
Caution: For clarification, it is necessary to consider
the level of vibrations in specific conditions of use in
all operating modes, e.g. the time when the power
tool is switched off except for the operation time,
and when it idles, i.e. performs no work. This may
substantially decrease the exposition level during the
whole operating cycle.
Minimize the risk of vibrations, use sharp chisels, drill
and blades.
44
Publicidad
