Nilfisk-Advance Adgility Instrucciones De Uso página 8

1. DUST BAG INSTALLATION
a) Open the triangular shaped dust bag cover by gently
pressing one end of the locking bar to release the locking
mechanism.
b) Grasp the cover in your hand, lifting the upper corners of
the cover away from the vacuum housing.
c) Slide the bottom edge of the cover away so the hinges on
the cover slip out of the housing.
d) Inside the dust bag cavity a round foam filter helps to
protect the motor. Be sure this filter is in place prior to
installation of the dust bag.
f) Gently unfold the new dust bag. Place the new bag inside
the machine making sure that the corners of the bag do not
prevent the cardboard plate from resting securely on the
housing
g) Place the cardboard plate onto the exterior lip of the cavity;
make sure that the cardboard plate is fitted
behind the two small clips on the exterior lip.
NOTE: The triangular shaped cardboard plate must be
placed evenly on the exterior housing lips in order for the dust
bag cover to be properly installed.
h) Replace the dust bag/hose inlet cover. First grasp the
cover in your hand, and insert the lower cover hinges into
the indentations. Be sure the dust bag cardboard plate is
resting evenly on the lips of the cavity. Close the cover,
and make certain it clicks into place.
2. BELT
The belt locking clip is designed to hold the vacuum cleaner
securely around your waist while working.
To connect: Wrap the belt around your waist. Adjust it to the
desired size, by fitting the two nylon parts together.
Then insert the toothed connector into the belt buckle until it
snaps into place.
Disconnect: To disconnect the belt when work is finished,
gently squeeze the outer clips together, and pull connector
out of belt buckle.
To adjust the belt for individual comfort:
Larger: Hold the belt locking clip in one hand and slide the
nylon belt until a loop is formed. Pull the belt locking clip to
adjust the slack in the nylon belt.
Smaller: Pull the loose end of the nylonbelt until adjusted to
desired size.
3. HOSE CONNECTION
Fit the bent end of the hose into the opening on the
machine cover. Press and turn about one-half turn to
ensure a secure fit.
4. WAND ASSEMBLY
a) To connect the wand sections together, simply insert one
section into the other, giving the two assembled sections
a firm push.
b) Adjust the length of the telescopic wand by pressing its
button and altering the wand length. When vacuuming
stairs it is recommended to that the wand is adjusted to its
shortest length.
8
5. TOOLS
The accessories shown in the pictures may vary from model
to model.
Floor nozzle, one way for brush (hard floor) or smooth for
carpet.
Round rotating dust brush useful tool for off floor
dusting.
Crevice Tool designed for cleaning in narrow spaces like
furniture, radiators, corners and joints.
7. ACCESSORY LOOPS
The belt is equipped with loops to conveniently hold the
vacuum's accessories. In addition, the power cord can be
held in place on the belt by snapping the nylon loop around
it.Always wind up the cord starting at the machine.
8. START/STOP
Convenient finger-tip on / off button
9. SUCTION CONTROL
The suction control in the hose handle lets you regulate the
air-flow to prevent the nozzles from fastening to the surfaces
you are vacuum cleaning.
10. EXHAUST FILTER
The exhaust cover is easily removed for filter changes
a) Grasp the cover in your hand.
b) Release the locking mechanism by gently pressing down
on one end of the locking bar.
c) Ease the upper corner away from the vacuum housing.
d) Slide the bottom edge of the cover away so the hinges on
the bottom edge of the cover slip out of the housing.
e) Remove filter holder and used filter.
f) Install new filter and secure with the filter holder.
g) Reinstall exhaust cover as in "Dust Bag installation"
11. WARNING!
Do not use the vacuum cleaner to pick up water. Wet
surfaces can expose the operator to possible electrical
shock.