Bojungle B725000 Instrucciones De Uso página 29

Key 11 timing key: press the first time to turn on the first indicator light, press the second time to turn on the second
•
light, press the third time to turn on the third light; press the fourth time to turn off the timing function, and so on.
Select timing.
When the remote control is not in use, it can be placed in the bag (K7 in Figure K-2) where the remote control is placed to
prevent loss.
Function introduction of electric toys (image 60-62):
61:. Use 2 AA batteries for power supply, use a screwdriver to loosen the battery cover screws until the cover can be taken out,
take out the cover, and install it according to the positive/negative polarity direction of the logo. Insert the battery, then close
the cover and tighten the screws, and use the same steps to remove the battery;
Warning: The screws of the battery cover must be locked, otherwise there will be liquid leakage, which will be a safety
risk! Batteries must be inserted with correct polarity! Do not install it in reverse, otherwise it will not be powered on!
Non-rechargeable batteries cannot be charged! Rechargeable batteries should only be charged under adult supervision!
Rechargeable batteries should be removed from the product before charging! Different types of batteries and old and new
batteries cannot be mixed! Exhausted batteries should be removed from the product! Dispose of immediately and keep
away from children!
• The rotation control key is shown as (① in Fig. 60), press it once to start the rotation function, press it a second time to
stop the rotation, and this cycle operates to control the rotation function.
The vibration control button is shown as (② in Fig. 60), press once to start the 1st gear (small gear) vibration, press the
•
second press to increase to the 2nd gear (maximum gear) vibration, press the third press to stop the vibration, This
cycle operates to control the vibration function.
The light control key is shown as (③ in Fig. 60), press once for blue light, press for second time for green light, press for
•
third time for blue-green mixed light, press for fourth time to turn off light, and so on. Operate to control the vibration
function
• 62: Night lights can be projected on the ceiling, and when the rotation function is activated, a rotating starry sky
pattern will appear as a reference starry sky pattern.
Special note: The three keys described above can be used by pressing any one of the keys to activate individual functions,
or to activate all functions at the same time!
Introduction to the function and use of the crib (image 63-74)
63: First lock the crib. Step 1 to lock the crib, fix the swing arm of the main unit with one hand, and use the other hand to lock
the lever, push into the lock seat until you hear a click.
40: Use your foot to move the brake lever of the wheelto control the brake, and move the brake lever of the wheel to the
position shown in (Fig. 41) A for braking state.
Warning: When using the crib, make sure the wheels are on the brakes!
Do not touch the brake lever with bare feet
64-68: To open low windows: first open the bedside opening and closing zippers at both ends, and pull them all the way to the
bottom of the inner lining to open the upper detachable tubular structure and use the index finger of one hand to lock the
second lock. Press the button in, push a lock button with the other index finger, and lift the upper detachable tubular structure
upward at this time; then open the other end with the same steps and methods to open the low. Finally, the upper detachable
tubular structure is fastened to the fixing buckle of the inner substrate portion by the steps and methods of (Fig. 68), as shown
in (Fig. 68). Step 2 shows the snapped upper detachable tubular structure.
Warning: When opening low windows, make sure that the second lock and the first lock are fully opened before they can
be removed normally! Otherwise, the low windows cannot be opened normally!
Connect the adult bed, move the shaker to a position close to the adult bed, check the height of the crib and the adult mattress.
WARNING: The height of the adult mattress should always be level or greater than the crib's side supports up to 20mm as
shown in (Fig. 76) and (Fig. 77)!
69-74: Take out any one of the fixing straps and fasten the anchor buckle at any end of the fixing belt into any one of them. The
anchor buckle and then form a loop from the bottom of the parent bed structure to the top and fasten the other end of the
anchor buckle into another fixed buckle. The other fixing strap is also installed on the other side of the shaker; for easier
installation, before the fixing strap is fastened, we suggest that the shaker should be kept a certain distance from the adult bed.
!