HIKOKI RP 250YBL Instrucciones De Manejo página 8

English
- Carefully pull back and remove the fleece filter
bag (4) from the suction opening (9). Seal the
flange of the fleece filter bag by folding over the
cover.
- Dispose of the vacuumed material in accordance
with legal regulations.
12. Maintenance
12.1 General Instructions
Before performing any maintenance, always
switch off the device and remove the mains
plug.
Clean the device (see section 11.).
For maintenance by the user, the dust extractor
must be taken apart, cleaned and maintained, to the
extent possible, without endangering maintenance
staff or other people.
Preventive Measures
Appropriate preventive measures include: cleaning
the device before disassembly; providing local
filtered forced ventilation where the dust extractor is
disassembled; cleaning of the maintenance area
and providing suitable personal protective clothing
and equipment.
12.2 Reduction in suction power
If the suction power decreases, carry out the
following steps:
1. Clean the filter cassettes by activating the elec-
tromagnetic vibrator (set switch (1) to the "RA"
position).
2. Empty the container or replace the fleece filter
bag (4).
3. Replace the filter cassettes (13), or rinse them
under running water, dry them and then replace.
12.3 Renew the filter cassettes (13)
Shake the filter cassettes (13) once again before
replacing the filters by switching on the electromag-
netic vibrator (set switch (1) to the "RA" position).
Use a coin or a similar object to turn the locking
knob (10) on the locking bar (11) counter-clockwise
through 90° and push the bar (11) to the rear. Swing
up the hood and pull up the filter cassettes (13) to
remove them. Seal the removed filter cassettes
immediately in a dust-tight plastic bag and dispose
of them in accordance with regulations. Insert new
filter cassettes, ensuring they are correctly and
securely in place.
12.4 Motor protection filter
Regularly check the motor protection filter. If the
motor protection filter (12) is contaminated, this indi-
cates that the filter cassettes (13) may be defective:
- Replace the filter cassettes (13).
- Replace the motor protection filter (12), or rinse it
under running water, dry it and then replace.
8
12.5 Water sensor
IMPORTANT - Clean the water
sensor regularly and check it for
signs of damage.
13. Troubleshooting
If the volume flow control display (2) lights up, this
indicates that the fleece filter bag must be emptied.
Reduction in suction power:
See the instructions in the section on Cleaning.
• Filter cassettes (13) soiled? Clean the cassettes.
• Fleece filter bag (4) full? Replace the filter bag.
• Container (8) full? Empty the container.
• Motor protection filter (12) clogged? - See
section 12.
• Nozzle, tubes or hose blocked? Clean.
Device will not start:
• Is the plug in the plug socket?
• No power from mains?
• Mains lead OK?
• Device hood correctly closed?
• Has the water sensor cut off? - Empty the
container; then switch on and off again.
• Switch (1) in "RA / A" position? - Set to "I" posi-
tion. See section 9.1.
• The dust extractor is not switched on or off by
means of a power tool, even though switch (1) is
set to the "RA / A" position. - Connect the power
tool to the plug socket (3).
14. Accessories
Use only genuine HiKOKI accessories. See
page 157.
Use only accessories that fulfil the requirements
and specifications listed in these operating instruc-
tions.
15. Repairs
Replacing supply cord
If the replacement of the supply cord is necessary,
it has to be done by HiKOKI Authorized Service
Center to avoid a safety hazard.
CAUTION! In the operation and maintenance
of power tools, the safety regulations and
standards prescribed in each country must be
observed.