Publicidad
Idiomas disponibles
Idiomas disponibles
NOTICE:
When attaching the water hose con-
nector and coupling sleeve, attach them securely.
Otherwise, the water hose connector or coupling
sleeve may come off when you open the faucet.
Connecting/disconnecting the nozzle
CAUTION:
Always lock the trigger of the
trigger gun when connecting/disconnecting the
nozzle.
CAUTION:
When connecting the nozzle to the
trigger gun, connect it securely and make sure
that it does not come off.
CAUTION:
When connecting or disconnect-
ing the nozzle, do not rotate it forcibly. Otherwise,
the nozzle may break or come off and cause an injury.
Insert the end of the nozzle into the slot on the trigger
gun, and turn it in the direction of the arrow as shown in
the figure while pressing the nozzle toward the trigger
gun. To disconnect the nozzle, turn the nozzle in the
reverse direction while pressing it toward the trigger
gun, and then pull it out.
► Fig.15: 1. Trigger gun 2. Slot 3. End of the nozzle
Connecting the foam nozzle
Optional accessory
CAUTION:
Always lock the trigger of the
trigger gun when connecting/disconnecting the
nozzle.
NOTICE:
Use only neutral detergents. Do not
use household detergents, acid detergents, alka-
line detergents, bleaches, solvents, flammable
material, or industrial grade solutions, which may
damage the machine or your property. Prepare
cleaning solution as instructed on the solution
bottle, and always test it in an inconspicuous
place in advance.
NOTICE:
If a highly viscous detergent is used,
the nozzle is likely to clog. When using the high
viscosity detergent, dilute the detergent by add-
ing water to the bottle before use.
NOTE: When using the foam nozzle, the detergent
in the bottle is diluted with the water supplied by the
machine and sprayed. You do not have to dilute the
concentration of detergent in the bottle more than
necessary. Adjust the concentration of detergent
while checking the usage conditions.
NOTE: If the foam nozzle is tipped on its side, the
detergent may spill.
Prepare detergent before using the foam nozzle.
1.
Remove the nozzle from the tank by rotating the
nozzle counterclockwise. Attach the nozzle to the trig-
ger gun.
► Fig.16: 1. Nozzle 2. Trigger gun
2.
Pour the detergent into the tank, and attach the
tank to the nozzle by turning it in the direction shown in
the figure.
► Fig.17: 1. Tank
OPERATION
WARNING:
direct it toward yourself or others. The water jet is
dangerous and can hurt you or others.
WARNING:
never hold the object that you are cleaning or
place your hands and feet near the water jet.
CAUTION:
Stay alert to the rebound of the
water jet and blown objects. Do not bring the
nozzle to the object closer to 30 cm (11-3/4").
CAUTION:
Do not run the high pressure
washer without water for longer than 1 minute.
CAUTION:
Do not operate the high pressure
washer for an extended period of time. This may
cause overheating or fire. Also, long-term use may
cause vibration disorder.
CAUTION:
Be aware of the direction of the
wind. If the detergent gets into your eyes or mouth,
rinse with fresh water immediately and seek medical
attention if necessary.
CAUTION:
Hold the trigger gun firmly. The
trigger gun recoils when you pull the trigger.
CAUTION:
Always hold the trigger gun by the
grip and barrel when ejecting water jet.
NOTICE:
Avoid using the high pressure washer
for longer than 1 hour. After using it for 1 hour,
leave a same length of intermission.
NOTICE:
To protect the mechanism of the high
pressure washer, do not use water hotter than
40°C (104 °F).
NOTICE:
Be careful not to pull the trigger gun
forcibly during operation. It may cause the high
pressure washer to fall over.
NOTICE:
When suspending the operation for a
long time, switch off the high pressure washer
and squeeze the trigger to discharge the remain-
ing water fully.
If the high pressure washer is left for a long time while
maintaining high pressure, it may not restart. In this
situation, switch off the high pressure washer, sup-
ply water from a faucet to the inlet and squeeze the
trigger with keeping the water supply for a while. And
then, switch on the high pressure washer.
NOTICE:
Do not use the machine in an over-
turned position. Doing so may cause malfunction.
► Fig.18
Before operating the machine, remove the nozzle from
the trigger gun.
1.
Open the battery cover and install the battery
cartridges into the high pressure washer and then lock
the battery cover.
► Fig.19: 1. Battery cartridge 2. Battery cover
2.
Connect one end of the high-pressure hose to
the trigger gun and the other end to the high pressure
washer.
18 ENGLISH
Do not touch the water jet or
When shooting the water jet,
Publicidad
