Descargar Imprimir esta página

HIKOKI H 41E Instrucciones De Manejo página 8

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 31
English
5) Service
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of
children and infi rm persons.
DEMOLITION HAMMER SAFETY
WARNINGS
Safety instructions for all operations
1. Wear ear protectors.
Exposure to noise can cause hearing loss.
2. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
3. Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could
give the operator an electric shock.
ADDITIONAL SAFETY WARNINGS
1. Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3. When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Do not touch the bit during or immediately after
operation. The bit becomes very hot during operation
and could cause serious burns.
5. Before starting to break, chip into a wall, fl oor or ceiling,
thoroughly confi rm that such items as electric cables or
conduits are not buried inside.
6. At the start of work, confi rm screw tightening.
7. When working at a highly elevated location, pay attention
to articles and persons below.
8. Wear protective shoes to protect your feet.
9. Wear a dust mask.
Do not inhale the harmful dusts generated in chiseling
operation. The dust can endanger the health of yourself
and bystanders.
10. Mounting the tool
○ To prevent accidents, make sure to turn the switch off
and disconnect the plug from the receptacle.
○ When using tools such as bull points, cutters, etc.,
make sure to use the genuine parts designated by our
company.
○ Clean the shank portion of the bull point. Then smear the
shank portion with the grease or machine oil.
11. Be sure to grip the handle and side handle or cylinder
case cover during work. Do not hold by the grip during
work. If you pull it by mistake, the bull point could jump out.
12. RCD
The use of a residual current device with a rated residual
current of 30mA or less at all times is recommended.
13. Make sure to securely hold the tool as shown in Fig. 11
during operation.
NAMES OF PARTS (Fig. 1–Fig. 11)
Tool Shank
Front Cap
Grip
Grip (B)
On-lock Switch
Trigger Switch
Handle
Nameplate
Set screw (Under the Plate)
Plate
Tail Cover
Housing
Side Handle
Cylinder Case Cover
Band
Handle Bolt
Mount
Band attachment area
Impact rate selector switch
Display lamp
SYMBOLS
WARNING
The following show symbols used for the machine.
Be sure that you understand their meaning before
use.
H41ME : Demolition Hammer
Low Vibration Handle
To reduce the risk of injury, user must read
instruction manual.
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive
2012/19/EU on waste electrical and electronic
equipment and its implementation in
accordance with national law, electric tools
that have reached the end of their life must
be collected separately and returned to an
environmentally compatible recycling facility.
V
Rated voltage
P
Power Input
Bpm
Full-load impact rate
Weight
(According to EPTA-Procedure 01/2014)
kg
Switching ON
Switching OFF
8

Publicidad

loading