Facom CL3.C10SD Manual Original página 20

Hot/Cold pack delay
Some chargers have a Hot/Cold Pack Delay feature: when the charger detects a battery that is hot, it automatically starts a Hot Pack Delay,
suspending charging until the battery has cooled. After the battery has cooled, the charger automatically switches to the Pack Charging mode.
This feature ensures maximum battery life. The red light flashes long, then short while in the Hot/Cold Pack Delay mode.
Leaving the battery pack in the charger
The charger and battery pack can be left connected with the charge indicator showing «Pack Charged».
Weak battery packs: Weak batteries will continue to function but should not be expected to perform as much work.
Faulty battery packs: This charger will not charge a faulty battery pack. The charger will indicate faulty battery pack by refusing to light
or by displaying problem pack or charger.
Note: This could also mean a problem with a charger.
Problem Power Line
Some chargers have a «Problem Powerline indicator». When the charger is used with some portable power sources such as generators or
sources that convert DC to AC, the charger may temporarily suspend operation, flashing the red light with two fast blinks followed
by a pause. This indicates the power source is out of limits.
Important Charging Notes
1. Longest life and best performance can be obtained if the battery pack is charged when the air temperature is between18 –24 ˚C
(65 ˚F and 75 ˚F). DO NOT charge the battery pack in an air temperature below +4.5 ˚C (+40 ˚F), or above +40.5 ˚C (+105 ˚F).
This is important and will prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to touch while charging. This is a normal condition, and does not indicate a
problem. To facilitate the cooling of the battery pack after use, avoid placing the charger or battery pack in a warm environment
such as in a metal shed, or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp or other appliance;
b. Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights;
c. Move charger and battery pack to a location where the surrounding air temperature is approximately 18–24 ˚C (65 ˚F–75 ˚F);
d. If charging problems persist, take the tool, battery pack and charger to your local service centre.
4. The battery pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT
CONTINUE to use under these conditions. Follow the charging procedure. You may also charge a partially used pack whenever you
desire with no adverse affect on the battery pack.
5. Foreign materials of a conductive nature such as, but not limited to, grinding dust, metal chips, steel wool, aluminum foil, or any
buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when
there is no battery pack in the cavity. Unplug charger before attempting to clean.
6. Do not freeze or immerse charger in water or any other liquid.
WARNING: Shock hazard. Don't allow any liquid to get inside charger. Electric shock may result.
WARNING: Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or cracks, return
to a service center for recycling.
Additional Important Safety Instructions for all Battery Packs
Battery type
The CL3.C10JD, CL3.C10RD and CL3.C10SD operate on 10.8 volt battery pack.
The CL3.BA1015 and CL3.BA1020 battery pack may be used. Refer to technical data for more information.
Storage Recommendations
1. The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold. For optimum battery
performance and life, store battery packs at room temperature when not in use.
2. For long storage, it is recommended to store a fully charged battery pack in a cool dry place out of the charger for optimal results.
NOTE: Battery packs should not be stored completely depleted of charge. The battery pack will need to be recharged before use.
NU-CL3.C10JD CL3.C10RD CL3.C10SD_1015.indd 20
20
2/29/2016 10:08:47 AM