Publicidad
Idiomas disponibles
Idiomas disponibles
Mounting method
Angle range
Wall
Fixed
Yoke (standard)
+45° to -90°
Hub (DP1053MTK)
+45° to -90°
Note: Class II, Div.1 and Simultaneous Presence Class I, Div. 2 and Class II will be
limited to 0° to +45° aiming range only.
WIRING - WIRING THE LUMINAIRE
1.
Unscrew six (6) driver door screws and allow driver door to hang on the hinge
provided in the housing. Note that the six screws are retained by additional
threads in the door, do not unthread them all the way out. Do not disconnect
the ground wire.
2.
Pull field wiring (maximum 12 AWG) into housing through any of the conduit
entries. See the product nameplate for supply wire requirements. Insert them
into the proper wago leverlock connectors (only use designated terminals shown
for field wiring) per the attached wiring diagrams using methods that comply
with all applicable codes. See Figures 1A & 1B.
3.
Close all unused conduit entries with conduit plugs provided. To prevent galling
and to ensure water tightness, lubricate conduit plugs with Eaton's Crouse-Hinds
series HTL lubricant before installing, and secure wrench-tight with at least five
(5) full threads engaged (42-52 ft.-lb. for 3/4" plugs)
4.
Close driver housing with driver door, making sure that all wires are safely inside
driver housing.
5.
Follow the screw tightening pattern, see Figure 2. Tighten captive closing screw
to 23 in.-lbs. (2.6 N-m). Ensure six (6) compression stoppers on driver door are in
contact with housing.
6.
Turn power on.
Note:
A maximum of 8 luminaires may be daisy-chained on a single circuit. See Figure 1C.
Variant
Signal
Line
Neutral
LED+
3L, 5L, 7L
LED-
Dimming-
Dimming+
If using optional gray and violet dimming wires provided, for Class 2 dimming control
circuit use only wires rated 600V minimum. Dimming circuit operates on 0-10 VDC,
dimmer is to be certified suitable for use in the environment (ex. Hazardous, Ordinary
locations, etc.) in which it is installed.
ACCESSORIES - SECONDARY RETENTION CABLE
1.
Two attachment points for secondary retention are provided, see Figure 3.
Either loop secondary retention cable through the attachment or clip on the
carabiner provided with SC831 accessory kit.
2.
Connect cable to a permanent structure or anchor (customer supplied).
3.
Remove any slack to ensure the cable is taut and confirm engagement of the
lock.
IF 1966 • 08/23
GROUND
Figure C
Mounting surface
Wall
Wall, Ceiling, Horizontal Surface/Ground
Wall, Ceiling, Horizontal Surface/Ground
Wire color for HV
Wire color for LV
LED driver
LED driver
Black/Orange
Black
Black/White
White
Red
Red
Blue
Blue
Gray
Gray
Violet
Violet
Copyright
©
WAGO LEVER LOCK TERMINALS.
WAGO LEVER LOCK TERMINALS.
D
D
TERMINALS FOR
FIELD WIRING
G
G
L
L
C
N
C
N
TERMINALS FOR
TERMINALS FOR
FIELD WIRING
FIELD WIRING
8
B
B
NOTES:
1.
EQUIPMENT GROUNDING CONDUCTOR TERMINATED TO HOUSING WITH RING TERMINAL.
2.
GRAY AND VIOLET DIMMING LEADS FROM DRIVER TO BE INDIVIDUALLY CAPPED OFF USING
WAGO LEVER LOCK TERMINALS.
D
PHOTOCELL
PHOTOCELL
LEGEND
LEGEND
A
A
FACTORY WIRING
FACTORY WIRING
FIELD WIRING
FIELD WIRING
L
LINE
L
LINE
N
NEUTRAL
N
NEUTRAL
C
CONTROL
C
CONTROL
C
G
GROUND
G
GROUND
8
LUMINAIRE 1
8
SOURCE
OF
SUPPLY
G
L
B
N
-
+
LEGEND
A
FACTORY WIRING
FIELD WIRING
L
LINE
N
NEUTRAL
CONTROL
C
G
GROUND
8
1
6
Figure 2
2023, Eaton's Crouse-Hinds Division
TERMINALS FOR
FIELD WIRING
MPCB
MPCB
CN1
-
CN1
-
+
+
GREEN
GREEN
L
L
OUTPUT
INPUT
OUTPUT
INPUT
N
N
DRIVER
DRIVER
DIMMING
DIMMING
TERMINALS FOR
FIELD WIRING
STANDARD WIRING
STANDARD WIRING
NOTES:
Figure 1A
1.
2.
GREEN
GREEN
G
G
D
N
N
7
L
L
L
L
INPUT
N
N
BLACK
BLACK
L
L
WHITE
N
WHITE
N
RED
C
RED
C
PHOTOCELL WIRING
PHOTOCELL WIRING
C
Figure 1B
LUMINAIRE 2
(UP TO 8 MAXIMUM)
G
L
N
7
7
MPCB
B
L
INPUT
G
N
DRIVER
L
N
THRU-FEED WIRING
Figure 1C
A
Mounting bracket
Side conduit entry
Hex screws to fix
mounting brackets to
7
5
3
2
4
BLUE
BLUE
RED
RED
RED
+
RED
+
BLUE
-
BLUE
-
GRAY
-
GRAY
-
VIOLET
+
VIOLET
+
TERMINALS FOR
FIELD WIRING
8
EQUIPMENT GROUNDING CONDUCTOR TERMINATED TO
GRAY AND VIOLET DIMMING LEADS FROM DRIVER TO B
WAGO LEVER LOCK TERMINALS.
MPCB
MPCB
CN1
BLUE
-
CN1
BLUE
-
RED
+
RED
+
5
6
TERMINALS FOR
FIELD WIRING
RED
3L, 5L,
+
RED
+
INPUT
OUTPUT
BLUE
OUTPUT
-
-
BLUE
DRIVER
DRIVER
GRAY
-
GRAY
-
DIMMING
DIMMING
VIOLET
+
VIOLET
GREEN
+
TERMINALS FOR
G
TERMINALS FOR
FIELD WIRING
FIELD WIRING
L
N
6
20Y64-3
TERMINAL, LEVER LOCK,
6
20Y64-3
TERMINAL, LEVER LOCK, 5
5
20Y64-2
TERMINAL, LEVER LOCK,
5
20Y64-2
TERMINAL, LEVER LOCK, 3
STANDA
4
20Y64-1
TERMINAL, LEVER LOCK,
4
20Y64-1
TERMINAL, LEVER LOCK, 2
3
0307886-2
3
0307886-2
2
0307886-1
+
-
2
0307886-1
1
20Z16-100
WIRE ASSEMBLY, (1) RING T
1
20Z16-100
WIRE ASSEMBLY, (1) RING TER
ITEM NO.
PART NUMBER
ITEM NO.
PART NUMBER
6
5
5
6
GREEN
G
TERMINALS FOR
CN1
BLUE
FIELD WIRING
-
RED
+
N
RED
+
OUTPUT
BLUE
-
L
GRAY
-
DIMMING
VIOLET
+
BLACK
L
WHITE
PHOTOCELL
N
RED
C
Back conduit entry
Mounting bracket
Hex screws to fix
LEGEND
mounting brackets t
FACTORY WIRING
FIELD WIRING
6
20Y64-3
TERMINAL, LEVER LOCK, 5-POS, W
Side conduit entry
L
LINE
5
20Y64-2
TERMINAL, LEVER LOCK, 3-POS, W
4
20Y64-1
TERMINAL, LEVER LOCK, 2-POS, W
N
NEUTRAL
3
0307886-2
WIRE, LED BOARD, #22 BLU
C
CONTROL
2
0307886-1
WIRE, LED BOARD, #22 RED
G
GROUND
1
20Z16-100
WIRE ASSEMBLY, (1) RING TERM., #1
ITEM NO.
PART NUMBER
8
5
6
Secondary
retention
hook
Figure 3
Page 2
7
M
L
INPUT
N
D
G
N
L
WIRE, LED BOARD,
WIRE, LED BOARD, #
WIRE, LED BOARD
WIRE, LED BOARD, #
DESCRIPTIO
DESCRIPTION
G
N
L
PHOTO
DESCRIPTION
7
Publicidad
