Publicidad
Idiomas disponibles
Idiomas disponibles
Warranty .........................................
2
Safety Rules ....................................
2-3
Unpacking .......................................
3
Assembly ......................................
4-6
Operation ......................................
6-7
Maintenance .....................................
7
Troubleshooting ...................................
8
Parts Illustration and List ........................
'10-13
Espariol ......................................
14-23
FULL ONE YEAR WARRANTY
If this product fails due to a defect in material or workmanship
within one year from the date of purchase, Sears will at its
option repair or replace it free of charge. Contact your nearest
Sears Service Center (1-80O-4-MY-HOME) to arrange for
product repair, or return this product to place of purchase for
replacement.
If this product is used for commercial or rental purposes, this
warranty will apply for 90 days from the date of purchase.
This warranty applies only while this product is used in the
United States.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman
Estates, IL 60179
CAUTION:
Always follow proper operating procedures as
defined in this manual -- even if you are familiar with use of
this or similar tools. Remember that being careless for even a
fraction of a second can result in severe personal injury.
BE PREPARED FOR JOB
• Wear proper apparel. Do not wear loose clothing,gloves,
neckties, rings, bracelets or other jewelry which may get
caught in moving parts of machine.
• Wear protective hair covering to contain long hair.
• Wear safety shoes with non-slip soles.
• Wear safety glasses complying with United States ANSI
Z87.1. Everyday glasses have only impact resistant lenses.
They are NOT safety glasses.
• Wear face mask or dust mask if operation is dusty.
• Be alert and think clearly Never operate power tools when
tired, intoxicated or when taking medications that cause
drowsiness.
PREPARE WORK
AREA FOR JOB
Keep work area clean, Cluttered work areas inviteaccidents,
Do not use power tools in dangerous environments, Do not
use power tools in damp or wet locations,Do not expose
power tools to rain,
Work area should be properly lighted.
•
Keep visitors at a safe distance from work area.
•
Keep children out of workplace. Make workshop childproof.
Use padlocks, master switches or remove switch keys to
prevent any unintentional use of power tools.
TOOL SHOULD
BE MAINTAINED
• Always unplug lathe prior to inspection.
• Consult manual for specific maintaining and adjusting pro-
cedures.
• Keep tool lubricated and clean for safest operation.
• Keep all parts in working order. Check to determine that
the guard or other parts will operate properly and perform
their intended function.
• Check for damaged parts. Check for alignment of moving
parts, binding, breakage, mounting and any other condition
that may affect a tool's operation.
•
A guard or other part that is damaged should be properly
repaired or replaced. Do not perform makeshift repairs.
(Use parts list provided to order replacement parts.)
•
Never adjust copy crafter while lathe is running. Disconnect
power to avoid accidental start-up.
Keep cutting tools sharp for efficient and safest operation.
KNOW HOWTO
USE TOOL
Use right tool for job. Do not force tool or attachment to do
a job for which it was not designed.
Avoid accidental start-up. Make sure that the tool is in the
"off" position before plugging in, turning on safety discon-
nect or activating breakers.
Do not force tool. It will work most efficientlyat the rate for
which it was designed.
Keep handsaway from chuck,centersand other movingparts.
Never leave tool running unattended. Turn the power off
and do not leave tool until it comes to a complete stop.
Do not overreach. Keep properfooting and balance.
Never stand on tool. Serious injury could occur if tool is
tipped or if centers are unintentionallycontacted.
Know your tool. Learn the tool's operation, application and
specific limitations.
Handle workpiece correctly. Mount firmly in holding
devices. Protect hands from possible injury.
Turn machine off if workplace splits or becomes loose.
Use cutting tools as recommended in "Operation."
WARNING: For yourown safety,do not operate yourcopy
crafteruntil it is completelyassembledand installedaccordingto
instructions.
PROTECTION:
EYES, HANDS,
FACE, BODY, EARS
If any part of your copy crafter is missing, malfunctioning,
or has been damaged or broken, cease operating immedi-
ately until the particular part is properly repaired or
replaced.
• Wear safety gogglesthat comply with United StatesANSI
Z87.1 and a face shieldor dust mask if operationis dusty.
Wear ear plugsor muffsduringextended pedodsof operation.
Small loose pieces of wood or other objects that contact a
spinningworkpieca can be propelled at very high speed.
This can be avoided by keeping the work area clean.
• Clean copycrafter and la_e of all tools,wood scraps,etc.,
exceptworkpieca and necessary tools beforestartingopera-
tJon.
Never place your face or body in line with the chuck or
faceplate.
© Seam,Roebuck and Co.
2
Publicidad
