Publicidad
Idiomas disponibles
Idiomas disponibles
•
Never place your fingers or hands in path of cutting tools.
•
Never reach in back of the workpiece with either hand to
support the piece, remove wood scraps, or for any other
reason. Avoid awkward operations and hand positions
where a sudden slip could cause fingers or hand to move
into a spinning workpiece.
•
If the workplace splits or is damaged in any way, turn lathe
OFF and remove the workplace from the holders. Discard
damaged workpiece and start with a new piece of wood.
•
Use extra care when turning wood with twisted grain or
wood that is twisted or bowed -- it may cut unevenly or
wobble excessively.
KNOWYOUR CUTrlNG TOOLS
•
Dull, gummy, improperly sharpened or set cutting tools can
cause vibration and chatter during cutting operations.
Minimize potential injury by proper care of tools and regu-
lar machine maintenance.
THINK SAFETY
Safety is a combination of operator common sense and alert-
ness at all times when the lathe is being used.
•
For your own safety, read all rules and precautions in the
operator's manual before using this tool.
For eye protection,wear safety glasses complying with
United States ANSI Z87.1.
Do not wear loose clothing, gloves, neckties, rings,
bracelets or other jewelry that could get caught in moving
parts of machine or workpiece. Wear protective hair cover-
ing to contain long hair.
• Tighten all clamps, fixtures and tailstock before applying
power. Check to make sure that all tools and wrenches
have been removed.
With switch off, rotate workplace by hand to make sure
that there is adequate clearance. Start the machine on
lowest speed settingto verify that the workplace is secure.
Do not mount any workpieces that have splits or knots.
Never attempt to remount a between-centersturning if the
originalcenters on the turning have been altered or removed.
When remounting a between-centers turning that has non-
altered original centers, make sure that the speed is at the
lowest settingfor start-up.
•
Use extra caution when mounting a between-cantere turn-
ing to the faceplate, or a faceplate turning to between-cen-
ters, for secondary operations. Make sure that the speed is
at the lowest setting for start-up.
•
Never perform any operation with this tool where the work-
piece is hand-held. Do not mount a reamer, milling cutter,
drill bit, wire wheel or buffing wheel to the headstock spin-
dle.
• Never run the spindle in the wrong direction. The cutting
tool could be pulled from your hands. The workplace
should always turn towards the operator.
•
For spindleturning, ALWAYS positionthe tool rest above the
centedine of the workpiece and spindle (approximately_k").
Refer to Figure 1.
Check for shipping damage. If damage has occurred, a claim
must be filed with carrier. Check for completeness.
immediately report missing parts to dealer.
Your copy crafter is shippedcomplete in one carton.Separate all
parts from packingmaterials and check each one with the
unpackinglistto make certain all items are accountedfor before
discardingany packingmaterial,
if any parts are missing, do not attempt to assemble copy
crafter until the missing parts are obtained and properly
installed.
A
Carriage
B
Bracket (2)
C
Support Bar with Rack
D
Support Bar
E
Fine Adjustment Screw
F
Cutting Tool
G
Safety Shield
H
Guide with Set Screw (Model 24951 only)
I
Follower Assembly
J
Locking Handle (model 24951, qty 1: Model 24952, qty. 2)
K
Handle (4)
L
Lever with Grip
M
Pattern Support (2)
N
Tool Rest Base Assembly (Model 24951 only)
O
Carriage Support (Model 24951 only)
P
Carriage Support (Model 24952 only)
Q
Tool Rest Base Assembly (Model 24952 only)
A
B
D
E
I
Figure1 - Unpacking
Model 24951 Hardware bag (Part No. 18987.00) includes
guide pin, two bracket nuts, four bushings, two pattern bolts,
six spacers, one 5-0.8 x 10mm socket head bolt, one 6-1.0 x
12mm pan head screw, two 8-1.25 x 60ram socket head bolts,
two 8-1.25 x 40mm socket head bolts, four 8-1.25 x 25ram
socket head bolts, four 8-1,25 x 20mm socket head bolts, one
8-1.25 x 10ram set screw, four 8mm fiat washers, one 10ram
fiat washer, two 8-1.25mm hex nuts, two 10-1.5mm hex nuts,
4 and 6ram hex wrenches and 13/14mm open end wrench.
Model 24952 Hardware bag (PN 19078.00) includes guide
pin, two bracket nuts, four bushings, two pattern bolts, six
spacers, one 5-0.8 x 12ram socket head bolt, one 6-1.0 x
12mm pan head screw, two 8-1.25 x 60mm socket head bolts,
two 8-1.25 x 40ram socket head bolts, one 8-1.25 x 30mm
socket head bolt, two 8-1.25 x 25mm socket head bolts, two
8-1.25 x 20mm socket head bolts, four narrow 8ram fiat
washers, two regular 8mm flat washers, two 8ram lock
washers, one 10mm fiat washer, two 8-1.25mm hex nuts, one
10-1.5mm hex nuts, spacer, four 8-1.25 x 8ram set screws,
one 8-1.25 x 10mm set screw, brass pin, 4 and 6ram hex
wrenches and 13/14mm open end wrench.
Publicidad
