Costway OP70100 Manual Del Usuario página 11

SET-UP
Check the ground where the product will be set up for any sharp objects or debris. Do not install the product over
concrete or any hard surface.
Place the product on a soft level surface at least 2 meters from any structure or obstruction such as a fence, garage,
and house; overhanging branches, laundry lines or electrical wires.
Ensure the play area is free from hazards such as furniture, walls, sharp objects, other hard surfaces, etc.
Set up the product away from water and any potential fire hazards.
Keep the blower (air pump) and power cord away from areas of water and moisture. If water contacts the blower (air
pump), unplug the blower (air pump) power cord. Do not operate until the blower is completely dry.
Remove the product from the carry bag. If any, ensure the slide cover coming with the product stretches well from top to
end. Be sure to place as close to the power source as possible.
Stretch the inflation tube and attach it to the end of the blower (air pump). Ensure the inflation tube is securely attached
and in good condition. The inflation tube should be straight and untwisted. Reposition the blower (air pump) if
necessary.
If the product comes with water bags,please follow the undermentioned instruction,otherwise,overleap this
point.Spread out the product, place and fasten the empty water bags at the two sides of the product. Open the stopple
and fill water in the water bags until 80% full (about 22kg), push and close the stopple. make sure water bags are firmly
attached on the product and no water leakage before the product is fully inflated, and never allow children to play on the
slide without installing water bags. (refer to picture A)
If the product comes with dry and wet play functions, please follow the below steps:
For dry play, skip the following mentioned point and go to the point under the picture A, B, C, D, E to continue the set-up.
For wet play, note the number on the sprayer nozzle, and affix the sprayer nozzle to the corresponding number of hook
& loop fastener on the product. (refer to picture B, C). Attach the hose to water supply, turn on the water supply when
the product is fully inflated. (refer to picture D, E)
Push ground stakes through blower base holes. You may need to use a hammer for proper placement.
Make sure the blower (air pump) power switch is in the OFF position. Ensure the power connections are safely sited and
tripping hazard is minimized.
Place the inflation tube onto the blower(air pump) and place the long end of the strap through the loops. Wrap the strap
around the inflation tube and feed it through the black loop. (refer to picture F). Pull the strap tightly and secure the
reverse side to the black loop and affix it to the hook & loop fastener. Adjusting the direction of the inflation tube to
prevent bends or distortion that may impede the flow of air. (refer to picture G).
The blower (air pump) should be securely sited and affixed to the ground before use. Plug the blower (air pump) into an
approved grounded outlet.
Ensure the blower (air pump) is free from debris and securely sited to avoid tripping.
Turn the blower (air pump) power switch to ON. The continual air-flow blower (air pump) must be left ON at all time while
the product is being used. (refer to picture H)
The product should be fully inflated.
Ground support stakes are used for lawn ground surfaces. Hook and fit each provided ground stake through each loop
in the bouncer. To prevent overturn or lift during playing, push stakes firmly into the soil. Make sure the hooked end of
the stake is over the loop .The stakes should be placed level with or under the ground in order to reduce tripping
hazards. (refer to picture I)
Please check the age recommendation and user weights(printed on the product). You must not exceed the total weight
for the product.
Put the included play accessories if any for playing into the product. (refer to picture J, K)
If the product comes with support cushions at the sides, do not stand or sit on the cushions.
Make sure the water slide is fully inflated before children enter to play.
Hint: Air leak from the seams is necessary because the product is inflated by constant air flow and this leakage is
required to stop the product becoming over-inflated.
Hint: It is drawn user's attention to the orientation of the inflatable equipment installation in relation to the sun. The
sliding surface of the product shall not face to the sun as sunshine can glare the children's eyes when they are sliding
down along the slide.
It is normal that some water leaks from the edge of splashing pool.
TAKE DOWN
Make sure all children exit the product.
Make sure the product is free from foreign objects.
If the product comes with water bags, please follow the undermentioned instruction, otherwise, overleap this point.
11