Descargar Imprimir esta página

GE Profile GXCF35GBS Manual Del Propietário página 5

Dispensador de agua de electronico de tres temperaturas con enfriador de refrescos
Ocultar thumbs Ver también para Profile GXCF35GBS:

Publicidad

Idiomas disponibles

Idiomas disponibles

(rear of dispenser)
Drain
outletcap 2.
Draining the Dispenser
The dispenser
should
be drained
before
cleaning
the tanks and before
leaving tot
long
wlcations
or
absences.
1. UnI)lug
the dispense_:
Rein Dye tile water bottle ti'om the
dispenser
3. Put a container
that will withstand
hot
water under
the hot water tap. Press the
hot dJspel)ser
button
until the water is
cool (about
1 quart),
Add water to the
cold water resei','oir
(on top where
tile
bottle sui)plies
water)
as needed.
4. Dispense
water fl'om both buttons
into
container(s)
until no inore
water can be
dispensed
(about
1 quart
of water still
remains
in the dispenser).
5. Place a large bucket
beneath
tile drain
outlet
on the rear of the dispenser
6. Using a Phillips
screwdriver;
loosen
tile
scre_:s on tile bracket
coveting
tile drain
outlet
cap. Rotate tile bracket
out of
the way to allow access to the cap.
7. Remove
tile cap and silicon stopper
fl'om
tile drain
outlet and and allow water to
drain.
_Mter draining,
replace the stopper
and cap.
8, Rotate the bracket back into place and
tighten scrmvs.
Make sm'e to install a full bottle and
dispense
water fl'om tile hot water tap
before
i)lugging
in and turning
on tile
dispenser
(see Loading the Dispenser and
Start Up secdon).
Sanitizing and Cleaning the Water Tanks
IMPORTANT" Before initial use and periodically,
the water dispenser tanks must be sanitized to prevent unpleasant tastes in the
water and cleaned to remove mineral deposits that can impair flow.
To Sanitize:
1.
Befi)re
cleaning,
unplug the water dispenser.
NOTE: For first time installation,
skip steps
2-4.
2.
Empty the water bottle, then relllo\'e it fi'om tile dispenser
3.
Drain
tile water
tanks
(see Draining the Dispenser).
4.
Reinstall the sificon stopper and drain cap (see Draining
the Dispenser).
5.
DO NOT ADD BLEACH FIRST OR DIRECTLY TO THE
DISPENSER. Concentrated bleach may damage plastic.
Add 1/2 teasp(>(m
(2.5 ml) ot ordinary
6.0%
maximmn
household
bleach
to a 2 quart
(2 liter)
pitcher
filled with tap water.
6.
Pour
tile solution
in tile opening
at tile top of
the dispenser.
7.
Repeat
steps 5 and
6 until the dispenser
is flfll.
8.
Press the hot and
cold dispenser
buttons
until
the water just
begins
to flow fl'om the taps.
9.
Allow to sit tot 15-20
minutes.
10, Rinse out the bleach solution:
--
Drain
tile water
tanks
into a large bucket
(see Draining the DispeRser).
--
Make sure that tile silicon
stopper
is NOT installed.
--
IMPORTANT" Remove the separator and wipe out the
cold water reservoir (see Cleaning the Separator).
--
Clean,
then
reinstall
tile separator
and
collar
(see CleaRing the Separator).
--
Pore" approximately
1 gallon
(4
qtlarts
or
4 liters)
of fresh
tap water
into
the top and allow to drain
into tile bucket.
--
Flush with an additional
1 galhm
(4 quarts
or
4 liters)
of ti'esh
tap water and
allow to drain
into the bucket.
11. Reinstall the silicon stopper and drain cap
(see
Draining
the Dispenser).
12, Install a fi'esh water bottle
(see Loading the Dispenser).
13. Dispense I quart (1 liter) of water from each tap and
taste to make
sm'e tile 1)leach solution
is completely
rellloved.
If you continue to taste the chlorine from the bleach solution,
repeat steps 10-13 until the taste is gone.
14. Plug in tile dispenser.
ToRemove Mineral Deposits:
Mix 2 quarts (2 liters) of water with two quarts of vinegar ORmix 1 gaffeRof water (4 liters) with 16 ounces (454 g) of citric acid
crystals. Bleach does not remove mineral deposits. Do this in place of step 5 when removing mineral deposits.

Publicidad

loading