GRAPHITE 59G475 Manual Del Usuario página 9

An unbalanced blade causes the mower to vibrate violently
and there is a risk of an accident!
Check grass hopper and any damaged parts
Check the grass collector for signs of wear at more frequent intervals.
Replace any worn or damaged parts.
Use only original spare parts for maintenance.
The element exposed to the most severe wear is the blade. Check the
condition of the blade and its holder at regular intervals. When the blade
is worn, it must be replaced. If the mower vibrates excessively, it is a sign
of improper blade balance or impact deformation. In this case, replace the
blade.
Storing the mower:
• Disconnect the power cord.
• Allow the engine to cool down for approximately 30 minutes.
• Check, repair, or replace any power cord that shows signs of wear or
damage.
• Tighten or replace worn, loose, or damaged parts and clean thoroughly.
• Thoroughly clean the outside of the device with a soft brush and a cloth.
Do not use water, solvents, or pastes. Remove all grass and debris,
especially from the vents.
• Turn the device on its side and clean the blade and its guard. If blades
of grass are on or around the blade, remove them with a wooden or
plastic tool to protect the blade.
• To protect the mower from rust, wipe all exposed metal parts with an
oil-soaked cloth or spray a light grease spray.
• Keep the mower and extension cord in a closed, dry place out of the
reach of children to prevent unauthorized use or damage.
• Cover loosely with a tarpaulin for extra protection.
• In case of transportation, be sure to properly attach the device to the
vehicle.
• To reduce the storage space of the mower, the top handle can be folded
down as in fig. B.
Note: Do not press on the electric wire when folding the handle. Make
sure it does not get stuck or tangled when folding or unfolding the top
handle.
TROUBLESHOOTING
Before performing any maintenance or cleaning work, always
pull out the mains plug and wait for the blade to stop.
Symptom Possible problem
Power off
Power socket damaged
Damaged extension cord Check, replace if damaged.
The grass is too high
The device is
not working
Safety / overload
protection has been
activated
Damaged extension cord Check, replace if damaged
The mower
The grass bin is full.
works
The mower's internal
intermittently
wiring is damaged
Cutting height too low
The cutter blade tears the
The mower is grass or does not cut
not working
Machine underside badly
properly
clogged
Blade mounted upside
down
The cutter
Cutting blade blocked
blade does not
rotate
Blade nut / bolt loose.
Blade nut / bolt loose
Excessive
vibration /
Cutting blade damaged
noise
TECHNICAL SPECIFICATIONS
RATED DATA
Electric Lawn Mower 59G475
Parameter
Solution
Turn on the power
Use a working power outlet
Increase the cutting height
Allow to cool for a few
minutes and increase the
cutting height
Do not operate the switch
lever at this time as it will
extend the safety safety
reset time
Empty the grass collector.
contact service
Increase the cutting height
Replace the blade
Clean the device
Fix the blade in the correct
position
Serious damage, contact
the service center
Tighten the blade nut / bolt
Tighten the blade nut / bolt
Replace the blade
Value
Supply voltage
Power frequency
Rated power
Spindle speed without load
Level of security
Mowing diameter
Cutting height range
Number of cutting height positions
Grass catcher capacity
Protection class
Mass
Year of production
59G475 stands for both the type and designation of the machine
DATA ABOUT NOISE AND VIBRATIONS
Sound pressure level
Sound power level
Vibration acceleration value
Information on noise and vibration
The level of noise emitted by the device is described by: the level of the
emitted sound pressure LpA and the sound power level LwA (where K is
the measurement uncertainty). The vibrations emitted by the device are
described by the value of the vibration acceleration ah (where K is the
measurement uncertainty).
The following information: emitted sound pressure level LpA, sound power
level LwA and vibration acceleration ah have been measured in
accordance with EN 60335-2-77. The stated vibration level ah can be used
for the comparison of devices and for the initial assessment of vibration
exposure.
The stated vibration level is representative only for the basic use of the
device. If the machine is used for different applications or with different
work tools, the vibration level may change. The higher vibration level will
be influenced by inadequate or too seldom maintenance of the device.
The reasons given above may result in an increased exposure to vibration
during the entire period of operation.
To accurately estimate exposure to vibration, consider periods when
the equipment is turned off or when it is turned on but not in use.
After all factors have been carefully assessed, the overall vibration
exposure may be significantly lower.
In order to protect the user against the effects of vibrations, additional
safety measures should be implemented, such as: periodic maintenance
of the device and working tools, protection of the appropriate temperature
of hands and proper organization of work.
ENVIRONMENTAL PROTECTION
Electrically powered products should not be disposed
of with household waste, but should be disposed of in
appropriate facilities. Information on disposal can be
obtained from the dealer of the product or local
authorities. Waste electrical and electronic equipment
contains substances that are not neutral for the natural
environment. Non-recycled equipment poses a
potential threat to the environment and human health.
"Grupa Topex Spółka z ograniczoną odpowiedzialnością" Spółka
komandytowa with its registered office in Warsaw, ul. Pograniczna 2/4
(hereinafter: "Grupa Topex") informs that all copyrights to the content of
this manual (hereinafter: the "Manual"), including its text, photos,
diagrams, drawings, and its compositions belong exclusively to the Topex
Group and are subject to legal protection in accordance with the Act of
February 4, 1994, on copyright and related rights (i.e. Journal of Laws of
2006 No. 90 Item 631 as amended). Copying, processing, publishing,
modifying for commercial purposes the entire Manual and its individual
elements, without the consent of Grupa Topex expressed in writing, is
strictly prohibited and may result in civil and criminal liability.
WARRANTY AND SERVICE
The warranty conditions and the description of how to proceed in the event
of a complaint are included in the attached Warranty Card.
GTX Service Central Service NS. z o. o. Sp.k.
ul. Borderland 2/4
02-285 Warsaw
A network of Service Points for warranty and post-warranty repairs
available on the gtxservice.pl internet platform
Scan the QR code and visit gtxservice.pl
9
230 V AC
50 Hz
2000 W.
3500 min-1
IPX4
430 mm
20-70 mm
45 l
15 kg
LpA = 85 dB (A) K = 3 dB (A)
LwA = 94.5 dB (A) K = 1.84 dB (A)
ah = 3.02 m / s2 K = 1.5 m / s2
tel. +48 22 364 53 50
e-mail bok @ gtxservice.com
6
II