Publicidad
Idiomas disponibles
Idiomas disponibles
Battery charge indicator
When the on/off switch (10) is pressed in halfway or com-
pletely, the battery charge-control indicator (11) indicates
the charge condition of the battery for several seconds. The
indicator consists of three green LEDs.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
Temperature-dependent overload protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or the permitted bat-
tery temperature is exceeded, the electronics of the power
tool will switch off until the temperature returns to within the
optimum operating temperature range.
Practical advice
The torque depends on the impact duration. The maximum
achieved torque results from the sum of all individual
torques achieved through impact. Maximum torque is
achieved after an impact duration of 6–10 seconds. After
this duration, the tightening torque increases only minimally.
The impact duration is to be determined for each required
tightening torque. The tightening torque actually achieved
should always be checked with a torque wrench.
Guide values for maximum screw tightening torques
Figures given in Nm; calculated from the tensional cross-section; utilization of the yield point: 90% (with friction coefficient
µ
= 0.12). As a control measure, always check the tightening torque with a torque wrench.
total
Property Classes
Standard Screws/Bolts
according to
3.6
4.6
DIN 267
M6
2.71
3.61
M8
6.57
8.7
M10
13
17.5
M12
22.6
30
M14
36
48
M16
55
73
Tips
Before screwing larger, longer screws into hard materials, it
is advisable to pre-drill a pilot hole with the core diameter of
the thread to approx. 2/3 of the screw length.
Note: Ensure that no metal particles enter the power tool.
Recommendations for optimal handling of the battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of -20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
Bosch Power Tools
Screw applications with hard, spring-loaded or soft seats
When the achieved torques in an impact series are measured
during a test and transferred into a diagram, the result is the
curve of a torque characteristic. The height of the curve cor-
responds with the maximum reachable torque, and the
steepness indicates the duration in which this is achieved.
Capacity
A torque gradient depends on the following factors:
≥2/3
– Strength properties of the screws/nuts
≥1/3
– Type of backing (washer, disc spring, seal)
<1/3
– Strength properties of the material being screwed/bolted
together
Reserve
– Lubrication conditions at the screw/bolt connection
The following application cases result accordingly:
– A hard seat is a metal-to-metal screw application which
uses washers. After a relatively short impact duration, the
maximum torque is reached (steep characteristic curve).
Unnecessary long impact duration only causes damage to
the machine.
– A spring-loaded seat is also a metal-to-metal screw ap-
plication but uses spring washers, disc springs, studs or
screws/nuts with conical seats. It is also called a spring-
loaded seat when extensions are used.
– A soft seat is a screw application of e.g. metal on wood or
a screw application that uses lead washers or fibre wash-
ers as backing.
For a spring-loaded seat as well as for a soft seat, the max-
imum tightening torque is lower than for a hard seat. Also, a
clearly longer impact duration is required.
5.6
4.8
6.6
4.52
4.8
5.42
11
11.6
13.1
22
23
26
37.6
40
45
60
65
72
92
98
110
Occasionally clean the ventilation slots and the terminals on
the battery using a soft brush that is clean and dry.
Belt clip (see figure E)
You can use the belt clip (17) to hang the power tool on a
belt, for example. You then have both hands free and the
power tool is always at hand.
Coloured clip (see figure F)
You can use the coloured clip (18) to individually identify the
power tool.
High-strength Bolts
5.8
6.8
6.9
8.8
6.02
7.22
8.13
9.7
14.6
17.5
19.7
23
29
35
39
47
50
60
67
80
79
95
107
130
122
147
165
196
1 609 92A 7X1 | (15.07.2022)
English | 17
10.9
12.9
13.6
16.2
33
39
65
78
113
135
180
215
275
330
Publicidad
