Uline HOOVER H-3482 Manual Del Usuario página 5

RECOVERy TANk (LOWER TANk)
The recovery tank holds the dirty solution that is picked
up from the carpet. When the recovery tank is full, the
automatic "shut-off" will engage (see page 3) and the
tank must be emptied.
WARNING! To reduce the risk of electric shock,
unplug before cleaning or servicing.
M
N
Figure 24
P
Figure 26
1. Step on handle release pedal (M) and lower handle
until it rests on the floor. Rotate recovery tank latches
(N) outward (one on each side of tank). Lift tank off
of cleaner and carry it to a sink or drain.
(See Figure 24)
2. Unlatch back part of tank lid and remove lid. Empty
tank. Pour dirty water out from the rear of the tank
(O) (See Figure 25)
3. The lid replaces in a hinge-like manner. Position the
front of lid under tabs (P) on front of tank. Rotate
lid down onto tank. Make sure that the lid is secure
on all sides before placing tank on cleaner. For full
suction, it is important that the recovery tank lid is
properly secured before cleaning. (See Figure 26)
4. Replace tank and press down to ensure that it is
properly seated in place. Rotate latches (N) (one
on each side of tank) inward to lock tank in place.
Raise handle to upright position and replace upper
clean solution tank. (See Figure 27)
BEFORE yOU CLEAN
1. Vacuum thoroughly. For carpet, use a vacuum
cleaner with an agitator for best results. Do not
use the 'SteamVac' spotter/carpet cleaner as a dry
vacuum cleaner.
2. Test for colorfastness. Mix detergent and water
according to the instructions under "Fill solution tank".
Wet a white absorbent cloth with the solution.
PAGE 5 OF 24
INSTrUCTIONS CONTINUED
Figure 25
O
N
Figure 27
In a small, hidden area, gently rub the surface with
the dampened cloth. Wait ten minutes and check
for color removal or bleed with white paper towel
or cloth. If surface has more than one color, check
all colors.
3. When cleaning entire floor, move furniture out of
area to be cleaned (may not be necessary if only
high traffic areas are to be cleaned). For furniture
too heavy to move, place aluminum foil or wax
paper under legs. This will prevent wood finishes
from staining carpet. Pin up furniture skirts
and draperies.
4. Pretreat spots and heavy traffic areas with a
carpet precleaner.
5. To prevent staining, use plastic or aluminum foil to
protect wood or metal surfaces from possible water
spray.
6. To avoid wetting and possible damage to wood
floors underneath area rugs/carpet, either move
area rugs/carpet to a non-wood bare floor
surface or place waterproof material (e.g., plastic)
underneath them before cleaning.
CLEANING CARPET
1. Fill clean solution tank (upper tank) according to
instructions. (See Figures 17-23)
2. Move speed selector to Gentle Scrub for gentle
cleaning or Power Scrub for normal cleaning.
3. Dry hands and plug cord into a properly grounded
outlet.
WArNING! Do not clean over floor
electrical outlets.
4. To avoid walking on damp carpet, start at the end
of the room farthest from the door or path to sink
where tanks will be emptied and filled.
5. Step on handle release pedal and lower handle to
operating position; turn cleaner ON.
6. Squeeze trigger to release cleaning solution and
slowly push cleaner forward (equals one wet stroke).
7. Continue to squeeze trigger and slowly pull cleaner
back toward you (second wet stroke).
8. Release trigger and slowly push cleaner forward
over area just sprayed with solution (dry stroke).
9. Then slowly pull cleaner back toward you without
squeezing trigger (dry stroke). Overlap strokes by
one inch to help prevent streaking.
1114 IH-3482