GE 26 Manual Del Propietario Y Instalación página 41

Performance Data Sheet
SmartWater Filtration Sgstem-GE ®MWF Cartridge
This sgstem has been tested and certified in filter model GE MWF according to NSF/ANSI Standards/42 and 55 for reduction of the substances listed below. The
concentration of the indicated substances in water entering the sgstem was reduced to a concentration less than or equal to the permissible limit for water
leaving the sgstem, as specified in NSF/ANSI Standards/42 and 55.* (Safetg factors built in for unmetered usage)
Standard No. 42: Aesthetic effects
Substance NSF Specified Cha!!enge i Average % Average Product Max Permissible Product NSF Reduction I NSFTest
Reduction _Average Infiuent i Concentration Reduction Water Concentration Water Concentrat on Requirements _Report
Standard No. 53: Health effects
Substance I I NSF Specified Challenge Average %
Reduction I Average Influent Concentration
147,5000 cysts/L Minimum 50,O00cysts/L
47 MF/L 10_to ld fibers/L; fibers
0.009 mg/L
0.016 mg/L
0.08 mg/L
0.006 mg/L
greater than 10 Bm in lengt
0,009 mg/L_+ 10%
0,015 mg/L_+ 10%
0.08 mg/L _+10%
0.006 mg/L _+10%
0.148 mg/L 0,15 mg/L _+10%
0.002 mg/L 0.002 mg/L _+10%
0.0058 mg/L 0.006 mg/L _+10%
_L_+10%
0.222 mg/L 0.225 mg/L_+ 10%
0.015 mg/L 0.015 mg/L _+10%
0.015 mg/L 0.015 mg/L _+10%
<Based on the use of Cryptosporidium parvum oocysts
Capacity 300 gallons (I ,I 35 liters). Contaminant reduction determined by NSF testing.
Application Guidelines/Water Supply Parameters
Average Product ' Max Permissible Productl
Water Concentration
1 cyst/L
<1 MF/L
Water Concentration
N/A
NiA
0.0005 mg/L 0.003 mg/L
0.0005 mg/L 0.005 mg/L
0.001 mg/L 0.04 mg/L
0.0003 mg/L 0.002 mg/L
0.001 mg/L
0.00002 mg/L
0.0004 mg/L
O.O05mg/L
O.O005mg/L
0.001 mg/L
O.010mg/L
O.O002mg/L
0.002 mg/L
O.075mg/L
0.005 mg/L
O.O03mg/L
NSF Reduction
Requirements
_99,95%
_99%
NiA
N/A
N/A
N/A
NiA
N/A
N/A
NiA
N/A
N/A
N/A
N/A
N/A
NSFTest_
Report
J-00077721
J-00077707
J-00077708
J-00077717
J-00077718
J-00082185
J-00077722
J-00077723
J-00077726
J-00077727
J-00077728
J-00077729
J-00082184
J-00077730
J-00077705
Water Pressure
Water Temperature
It is essential that the manufacturer's recommended installation, maintenance and filter replacement requirements be carried out for the product to perform as advertised.
See Installation Manual for Warranty information.
Operating Specifications
• Pressure requirement: 40-120 psi (2.8-8.2 bar), non-shock
• Temperature: ]]-IO0°F (0.6-]8°C)
• Flow rate: 0.5 gpm (1.9 Ipm)
General Installation/Operation/Maintenance Requirements
• Flush new cartridge at full flow for 1-1/2 gallons (about three minutes) to purge
trapped ai_
• Replace cartridge when flow becomes too stow.
• Protect from freezing by removing filter cartridge when temperatures are
expected to drop below 33°F (1°C).Do not install sgstems in areas where
ambient temperatures mag go above IO0°F or below/40°R Do not install
on a hot water supplg.
Special Notices
• Installation instructions are included with the product when shipped.
• This drinking water system must be maintained according to manufacturer's
instructions, including replacement of filter cartridges.
• Do not use with water that is microbiologicallg unsafe or of unknown qualitg
without adequate disinfection before or after the system. Systems certified for
cyst reduction may be used on disinfected water that may contain filterable cysts.
•The contaminants or other substances removed or reduced by this water
treatment system are not necessarily in your water.
• Check for compliance with the applicable state and local laws and regulations.
• Note that while the testing was performed under standard laboratory conditions,
actual performance may vary. Systems must be installed and operated in
accordance with manufacturer's recommended procedures and guidelines.
• Installation and use MUSTcomply with all state and local plumbing codes. Do not
install if water pressure exceeds Z20 psi. If your water pressure exceeds 80 psi
(552 kPa), you should install a pressuredimiting valve. Contact a plumbing
professional if you are uncertain how to check your water pressure.
• Do not install where water hammer conditions may occur. If water hammer
conditions exist you must install a water hammer arrester. Contact a plumbing
professional if you are uncertain how to check for this condition.
• Where o backflow prevention device is installed on a water system, a device for
controlling pressure due to thermal expansion must be installed.
Tested and Certified by NSF International against ANSI/NSF Standards 42 and 53 in model GE MWF for the reduction of:
Standard No. 42: Aesthetic Effects
• Chemical
- Chlorine Taste and Odor
• Mechanical Filtration
- Particulate Reduction,ClassI
GE
Appliances
Appliance Park
Louisville, KY 40225
geopplianceparts.com
Standard No. 53: Health Effects
• Chemical Reduction
- Atrazine Reduction
- Endrin Reduction
- Benzene and Carbofuran Reduction
- 1,4 Dichlorobenzene and
2,4-D Reduction
- Lead and Lindane Reduction
- Mercurg and Toxaphene Reduction
• Mechanical Filtration
- Cgst and AsbestosReduction
REPLACEMENT
ELEMENT
© 2010 GE Compang PC61278B
41