DeWalt DCH966 Manual De Instrucciones página 34

ENglIsh
Wireless Tool Control™ pairing button on the separate device.
An LED on the separate device will let you know when your
tool has been successfully paired.
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: Be aware of the location of pipework
and wiring.

WARNING: Apply a pressure of approx. 44–66 lbs.
(20–30 kg) to the tool. Excessive force does not speed
up chiseling but decreases tool performance and may
shorten tool life.
Installing and Removing the Battery Pack
(Fig. K)

WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
NoTE: For best results, make sure your battery pack is
fully charged.
1. To install the battery pack
the battery pack with the rails inside the tool's handle
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does not disengage.
2. To remove the battery pack from the tool, press the
battery pack release button
battery pack out of the tool handle. Insert it into
the charger as described in the charger section of
this manual.
Proper Hand Position (Fig. L)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
IMpoRTaNT: The tool must be held with two hands at all
times when in use.
Horizontal Applications (Fig. L)
Proper hand position requires one hand on the bail/
loop style auxiliary handle
top handle 1 .
Vertical Applications (Fig. L)
Proper hand position requires both hands on the left
handle 5 and right handle
Switching On and Off (Fig. A, M)
To turn the tool on, set the on/off switch
turn the tool off, set the on/off switch
32
11 into the tool handle, align
12 and firmly pull the
8 with the other hand on the
3 .
2 to position 1. To
2 to position 0.
Demolition (Fig. L)

WARNING: Ensure that the cutting edge does not
show discoloration caused by too much pressure. This
may impair the hardness of the accessory.
Various types of chisels are available as an option.
1. Select the appropriate chisel. Clean the chisel shank
2. Insert the chisel and check whether it is properly locked.
3. Fit and adjust the bail/loop style auxiliary handle
make sure it is firmly tightened.
4. Hold the tool by the bail/loop style auxiliary handle
and the top handle 1
right handle 3 before switching ON.
5. The tool now runs in continuous operation.
IMpoRTaNT: alWaYs use two hands when operating
the tool. Refer to Proper Hand Position for the proper use
of the tool for both horizontal and vertical applications.
6. Always switch off the tool when work is finished and
before removing the battery pack.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the
risk of eye injury, always wear approved eye protection
when performing this procedure.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories

WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center.
or the left handle 5 and
WALT‑recommended
e
27 .
8 and
8