Descargar Imprimir esta página

Demeliss SA-2303 Manual página 8

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 19
NOTE: Always ensure the appliance, air outlet, air inlet, filter, filter cover and attachments
are clean and free of blockage, e. g. lint, hair or other objects.
NOTE: To avoid overheating and ensure performance, check the filter and filter cover for
blockage regularly and clean them accordingly, if necessary.
NOTE: The appliance features a memory function. After the appliance is switched off and
on again, it operates with the same settings of the temperature and air flow as previous
operation.
NOTE: If the malfunction occurs, unplug the appliance immediately from the power
supply. Wait a few seconds, connect the appliance to the power supply and switch it on
again. If the malfunction remains, do not use the appliance, until it has been checked and
repaired by a qualified electrician.
• high voltage protection activated: the appliance switches off automatically and the
temperature indicator (red)
• low voltage protection activated: the appliance switches off automatically and the
temperature indicators (red)
• NTC (negative temperature coefficient) abnormal: if the temperature detected by
the NTC is higher than the set value, the appliance will adjust the output power
automatically.
— Ensure the on/off switch is in the position O.
— Assemble the suitable attachment (volumizing brush, straightening brush, curling barrel,
nozzle) with a slight twist motion onto the main unit according to the desired application.
Ensure the release switch engages in position
— To remove the attachment, slide the release switch backward, hold it in position and then
remove the attachment from the main unit.
— Connect the appliance to the power supply.
— Set the on/off switch to the position I to switch on the
appliance.
— Press the air blow setting button repeatedly to select
the desired air blow. The respective indicator (blue)
turns on (
— Press the temperature setting & cold air button repeatedly to select the desired
temperature. The respective indicator (red) turns on (
: medium /
— Alternatively, during operation with the settings of low / medium / high temperature,
keep pressing the temperature setting & cold air button to activate the cold air function.
The temperature indicators (red) turn off and the appliance switches automatically to
the operating mode with high air blow. Release the temperature setting & cold air button
to deactivate the cold air function. The appliance operates with the previous settings.
— When the operation is finished, set the on/off switch to the position O to switch off the
appliance.
— Disconnect the appliance from the power supply. Place it on a heat-resistant surface to
let it cool down.
Styling and straightening hair with volumizing brush / straightening
brush
— Switch on the appliance. Set the desired temperature and air blow.
— Divide the hair into equal strands, preferably approx. 5 cm wide and 5 mm thick.
— Hold the appliance on the handle with one hand and the strand of hair with another hand.
— Brush the strand of the hair from the roots to the tips in a gentle and slow motion. To
achieve the best styling / straightening result, ensure the hair strand gets deep into the
inner areas of the bristles and close to the air outlets. Make sure not to keep the bristles
and air outlets on your hair for too long.
— Repeat the same operation for the other strands of the hair.
— Let the hair cool down before styling and straightening it further.
Curling hair with curling barrel
— Switch on the appliance. Set the desired temperature and air blow.
— Wait until the curling barrel reaches the set temperature.
— Hold the appliance on the handle.
— Roll a strand of hair (approx. 5 cm in wide, not too thick) onto the curling barrel for
approx. 5 - 8 seconds. Make sure not to keep the curling barrel on your hair for too long.
— Repeat the same operation over the entire strand of the hair.
— Let the hair cool down before styling it further.
Drying and styling hair with nozzle
— Ensure the hair is not too wet. Squeeze the excess moisture out of your hair with a towel
if necessary.
: low /
: medium /
: high).
is flashing.
are flashing.
.
: high).
1.
2.
: cold air /
: low /
8

Publicidad

loading