Nordic Home FT-530 Manual Del Usuario página 3

ENG
Product overview
1 2 3 4 5
6
14
13
7
12
15
8
11
10
9
Note: All images in this manual are for clarification
purposes. Discrepancies between the real object and
the picture on the drawing can occur.
1. Front protective guard
2. The rotor
3. Plastic Nut
4. Motor shaft
5. Oscillation button
6. Motor housing
7. Thumbscrew
8. Height adjustment ring
9. Rails
10. Cross connector
11. Upper pole
12. Lower pole
13. Speed buttons
14. Rear protective guard
15. Spinner
Features
When the installation is complete, connect to a
power outlet.
1. Fan speeds
0 = Off
1 = Low speed
2 = Medium speed
3 = High Speed
4
2. Starting Oscillation / movement
Press the oscillation button to start the movement.
Stop Oscillation / movement
Lift / pull up the oscillation button to stop
the movement.
3. Fan tilt
Adjust the tilt of the fan head to the desired angle by
gently loosening the knob on the fan's side. Adjust the
fan head up or down as desired and then secure
the knob.
4. Fan height
The height of the fan can be adjusted by gently
loosening the height adjustment ring. Raise or lower as
desired, then fasten the adjustment ring.
Maintenance and cleaning
The fan requires little maintenance. If the fan has
been broken and requires service contact
qualified personnel.
1. The fan must be disconnected from the mains
before cleaning and assembly.
2. To ensure adequate air flow to the fan motor, keep
the vents on the back of the fan motor free of dust.
Note do not dissemble the fan to remove dust.
3. Wipe the exterior with a soft wet cloth and
mild detergent.
4. Do not use abrasive cleaners or solvents to prevent
scratching the surface.
Do not use any of the following as a cleaner: gasoline,
or thinning solvent.
5. Protect the motor housing and internal parts from
water and other liquids.
Assembly of fan
1. Loosen the 4 sets of screws, washers and spring
washers which are fitted in the center section on the
stand and use them to assemble the extension pole
onto the base enclosure. (Fig.1)
2. Loosen the height adjustment ring, lift the internal
pole to the max height and prevent the internal pole
from slipping into the extension pole, then unscrew the
height adjustment ring. (Fig.2)
3. To attach the stand cover, slide the stand cover
down the extension pole. (Fig.3)
4. Reattach the height adjustment ring. (Fig.4)
5. Loosen the height adjustment ring from the
extension pole, and adjust the internal pole to the
desired height. (Note: The internal pole is inside the
extension pole. You can pull it out from the extension
pole.) (Fig.5)
6. To attach the head unit to the internal pole, loosen
the thumb screw on the bottom of the head unit.
Place the head unit on the internal pole and tighten
the thumb screw in alignment with the groove on the
internal pole. (Fig.6)
7. Unscrew the spinner clockwise (or take the spinner
out of the bag) and tighten the nut counterclockwise to
remove them both. Attach the rear protective guard to
the motor housing and tighten the nut. (Fig. 7)
8. Insert the fan blade on the motor fan shaft, and to
ensure that the spindle is mounted in the groove of the
fan blade. Turn the spinner counterclockwise to tighten
the fan blade. (Fig. 8)
9. Attach the front protective guard and rear protective
guard with grid clamp and attach the guard by
tightening nuts and bolts. (Fig. 9)
ENG
Fig.1 Fig.2 Fig.3
Loosen
Four screws
Fig.4 Fig.5 Fig.6
Thumb screw
Fig.7 Fig.8 Fig.9
5