Descargar Imprimir esta página

Scheppach HMS860 Traduccion Del Manual De Instrucciones Originale página 28

Ocultar thumbs Ver también para HMS860:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 84
-
Do not use tools in the presence of flammable
liquids or gases.
3.
Guard against electric shock
-
Avoid body contact with earthed or ground-
ed surfaces (e.g. pipes, radiators, ranges, re-
frigerators).
4.
Keep other persons away
-
Do not let persons, especially children, not
involved in the work touch the tool or the ex-
tension cord and keep them away from the
work area.
5.
Store idle tools
-
When not in use, tools should be stored in a
dry locked-up place, out of reach of children.
6.
Do not force the tool
-
lt will do the job better and safer at the rate
for which it was intended.
7.
Use the right tool
-
Do not force small tools to do the job of a
heavy duty tool.
-
Do not use tools for purposes not intended;
or example do not use circular saws to cut
tree limbs or logs.
8.
Dress properly
-
Do not wear loose clothing or jewellery, they
can be caught in moving parts.
-
Non-skid footwear is recommended when
working outdoors.
-
Wear protective hair covering to contain long
hair.
9.
Use protective equipment
-
Use safety glasses.
-
Use face or dust mask if working operations
create dust.
10. Connect dust extraction equipment
-
lf the tool is provided for the connection of
dust extraction and collecting equipment, en-
sure these are connected and properly used.
11.
Do not abuse the cord
-
Never yank the cord to disconnect it from the
socket. Keep the cord away from heat, oil and
sharp edges.
12. Secure work
-
Where possible use clamps or a vice to hold
the work. lt is safer than using your hand.
13. Do not overreach
-
Keep proper footing and balance at all times.
14. Maintain tools with care
-
Keep cutting tools sharp and clean for better
and safer performance.
28 | GB
-
Follow instruction for lubricating and chang-
ing accessories.
-
lnspect tool cords periodically and if dam-
aged have them repaired by an authorized
service facility.
-
lnspect extension cords periodically and re-
place if damaged.
-
Keep handles dry, clean and free from oil and
grease.
15. Disconnect tools
-
When not in use, before servicing and when
changing accessories such as blades, bits
and cutters, disconnect tools from the power
supply. If the planer shaft blocked when work-
ing by excessive feed force or clamping the
work piece, turn off the device and disconnect
it from the mains plug. Remove the workpiece
and make sure that the planer shaft runs free-
ly. Turn the power on, and run the operation
again with reduced feed force.
16. Remove adjusting keys and wrenches
-
Form the habit of checking to see that keys
and adjusting wrenches are removed from the
tool before turning it on.
17.
Avoid unintentional starting
-
Ensure switch is in "off' position when plug-
ging in.
18. Use outdoor extension leads
-
When the tool is used outdoors, use only ex-
tension cords intended for outdoor use and
so marked.
19. Stay alert
-
Watch what you are doing, use common
sense and do not operate the tool when you
are tired.
20. Check damaged parts
-
Before further use of tool, it should be care-
fully checked to determine that it will operate
properly and perform its intended function.
-
Check for alignment of moving parts, binding
of moving parts, breakage of parts, mount-
ing and any other conditions that may affect
its operation.
-
A guard or other part that is damaged should
be properly repaired or replaced by an au-
thorized service centre unless otherwise in-
dicated in this instruction manual.
-
Have defective switches replaced by an au-
thorized service centre.
-
Do not use the tool if the switch does not turn
it on and off.
www.scheppach.com

Publicidad

loading