Publicidad
Idiomas disponibles
Idiomas disponibles
• Use only original parts for accessories as well as
consumables and spare parts. Spare parts can be
obtained from your scheppach retailer.
• Please quote our article numbers as well as type
and production year in all your orders.
m ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
8. Assembly
m IMPORTANT!
You must fully assemble the appliance before us-
ing it for the first time!
8.1 Rubber feet (fig. 2)
Secure the four rubber feet (15) to the bottom side of
the equipment using the Allen screws (A) and washers
(B) supplied.
8.2 Planing blade cover (fig. 3-5)
• First remove the Phillips screw (19) and the fasten-
ing nut (10) on the planer blade cover (9) and the
fastening nut (6) on the swivel arm for planing blade
cover (9a).
• Push the planing blade cover (9) and the swivel arm
(9a) together.
• Retighten fastening nut (10) and Phillips screw (19).
• Fasten the assembly to the holes shown in Fig. 4/
Fig.5 using the fastening nut (6) and the star grip
screw (4)
8.3 Parallel stop (fig. 6 + 7)
• Now attach the parallel stop (8) to the machine hous-
ing and fasten it using the Allen screws (C).
8.4 Crank handle for thickness planer chip depth
(fig. 8)
• The crank handle (12) will be only plugged on the
spindle.
8.5 Chip extraction (fig. 10)
• To mount the extension of the chip extraction (5a),
open the Phillips screw on the extension. Fit both
parts (5, 5a) together and retighten the Phillips
screw.
8.6 Chip extractor - surface planing (fig. 11 + 12)
• Set the planing knife cover cpl. (9) in the upperst
position.
• Use the crank handle (12) to place the thicknessing
table (21) in the lowest position.
• Take the chip extractor (5) and hold the switching pins
(3) beside. Place the chip extractor (5) at a slightly slant-
ing angle on the machine and push it backwards. For
this you need to hold the switching pins (3) outwards.
• Now lock the chip extractor (5) with the switching
pins in the table. Attention! The machine won´t start
if the switching pins are incorrectly plugged in.
• Now you can fold the planing knife cover cpl. (9)
down again.
8.7 Chip extractor - thickness planing
(fig. 13 + 14)
• The parallel stop (8) needs to be removed for thick-
ness planing. Follow point 8.3 in reverse order.
• Hold the switching pins (3) outside and set the chip
extractor (5) on top of the machine.
• Now lock the chip extractor (5) with the switching
pins in the table. Attention! The machine won´t start
if the switching pins (3) are incorrectly plugged in.
9.
Installation
m IMPORTANT!
You must fully assemble the appliance before us-
ing it for the first time!
Before each use, check the following:
• Proper function of the on and off button, incl. the
emergency switch (if available).
• Locked disconnected protective equipment (fig.
1a - pos. 3)
by gradual opening of every separating protective
equipment to be able to turn the machine off and
checking that the machine cannot be turned on
whenever the protective equipment is open
• Brake
Switch on the machine at the start of work and allow
the machine to reach speed. Now switch the ma-
chine off again. The engine must come to a stand-
still within 10 seconds. Otherwise, there is a defect.
• Anti-kick claws (fig. 9 - pos. 20)
at least once per shift by a visual inspection to es-
tablish that they are in good working order, for exam-
ple, that the contact surface has not been damaged
by impacts and that the anti-kick claws (20) fall back
without hindrance due to their own weight;
www.scheppach.com
GB | 31
Publicidad
