Rubi DC-250 PYTHON Manual Del Usuario página 7

precision and comfort on all types of ceramic pieces.
31. Sliding is by means of greased and sealed ball bearings.
Changing the position from straight cutting to miter cutting or vice
versa, as well as adjusting the stops for repetitive cutting, must be done
33. When the machine is used outdoors, only extension cables intended for
outdoor use should be used. It should be noted that the extension cable
has to be fully unwound to get maximum power.
34. Before using the machine again, it should be carefully checked to
determine that it will function properly and be suitable for the function
for which it is intended. Any guard or other part that is damaged should
36. Remove the adjustment spanners and tools before starting the machine.
37.
machine.
38.
39. Once the machine is running, wait until the motor and the water supply
WARNING!
control and prevent potential kickback.
prevent it from being snagged or tangled on the piece being cut.
41.
without jerking and without forcing the motor. Improper operation can
break the part and seriously damage the blade.
with maximum precision by means of the tile clamping accessory for
43.
allows the cutting head to be positioned in the desired position.
44.
overheating.
46. If the motor stops for no apparent reason, you should wait a few minutes
as you will most likely have overloaded it and you should then moderate
the cutting speed.
47.
ground.
48.
49.
removing it from the cutting position.
Remember that the cutter must be unplugged from the power supply
adjustment and maintenance operations.
WARNING! Unplug the machine before carrying out any adjustments, repairs
or maintenance.
Proper cleaning and maintenance of the machine can extend its lifetime.
periods of inactivity.
Before performing cleaning, maintenance or repairs on the machine, as
unplugged.
Examine the machine's cords periodically and if they are damaged, have
them repaired by an authorised technical service.
Keep handles dry and clean and free of grease and oil.
In order to keep the machine in good condition, it is advisable to clean
through the cooling system. It is especially important to clean the water
water. Proper maintenance of the cutter will minimise the appearance
of rust spots.
We recommend cleaning the rolling tracks of the guide with a cotton
cloth dampened with water. No lubrication is necessary.
with the instructions in each country, at a selective collection point for
WARNING! Continued or improper use, constant changes in location and
transportation of the cutter can cause the components to become misaligned.
For proper functioning of the cutter, it is advisable to check the following
adjustment points:
a) Loosen screws A and nut B as indicated.
b) Gently tighten set screw C with the help of a 3 mm Allen key.
c) Check the head play and retighten nut B to lock the system, then retighten
screws A.
61.
a)
screws A as indicated.
b)
c)
machine has a transversal screw that allows the whole assembly to pivot
(rotate) with more precision.
d) Loosen screws A and rotate the square assembly using transversal screw C
e)
PERPENDICULARITY
a)
bottom of the blade touch the set square at the same time.
b) Replace the blade guard and then tighten the nut and knob.
PARALLELISM
63.
device as a reference.
a) Position the component so that the protrusion on the alignment device
the blade until it comes into contact, you will notice a slight noise when
the blade comes into contact with the protrusion. Mark that point as a
b) Move the blade head, without changing the position of the alignment
does not make contact at the same point, it will be necessary to adjust the
parallelism of the blade.
c) You can adjust the position of the motor by rotating it slightly.
d) Loosen screws A as indicated and rotate the motor using transversal screw
B. Repeat the same procedure and make sure that in both positions the
e) Once the blade is positioned, retighten screws A.
Store the tool in its packaging in a cool, dry place protected against cold and
direct sunlight.
the instructions in each country, at a selective collection point for the proper
Use only original spare parts supplied by the manufacturer. Repairs should
RUBI TOOLS USA INC.
EN
- 7 -