Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
Especificaciones generales: AF511103 is a wired thermostat. The user can adjust
the room temperature with the required temperature and get more comfortable
and economic heating/cooling.
• Daily and Weekly
• Precise Temperature
Program (7x24)
Measurement
• Different Mode Options
• Temperature
(Comfort Mode and
Calibration
Economy Mode)
• Heating/Cooling Modes
Thermostat - Buttons Functions
A
1
On/Off Button
2
Temperature Adjustment (To Increase)
3
Temperature Adjustment (To Decrease)
4
Weekly Program Button
5
Setting Button
6
Mode Button – Unlock Button
Screen Indicators
B
1
Day Indicator
2
Hour Indicator
3
Screen Lock
4
Room Temperature
5
Set Temperature
6
Economy Mode
7
Comfort Mode
8
Programming Mode
Cooling Indicator
9
- If the Cooling Indicator is blinking, the cooling unit is working.
- If the Cooling Indicator is steady, the cooling unit is not working.
Heating Indicator
10
- If the Heating Indicator is blinking, the heating unit is working.
- If the Heating Indicator is steady, the heating unit is not working.
11
Battery Indicator
Thermostat placement: Thermostat needs to be placed in the room which is
C
used most frequently. For instance; living room or lounge. Placing the Thermostat
in a spot that have air circulation like entrance of a room or side of window
should be avoided. Also anywhere close to heating/cooling units such as radiator,
stove and spots which get direct sun lights would not be suitable. Thermostat
needs to be located above the floor 150 cm height. Few trials may be made to find
the most convenient spot.
Battery placement: Before starting, power off the device connected to the
D
Thermostat and make sure that the energy is cut off. As shown in the picture
above, press the screwdriver forward from the space shown, bend the tabs
and separate the front cover. Insert 2 new AAA alkaline batteries in the battery
housing with the correct battery direction. Replace both batteries at the same
time. Then align the front part of your Room
Thermostat to the back and squeeze it towards the back.
Low Battery Warning: When the " " icon appears on the screen, it means "low battery
warning". It is recommended to replace the batteries when this warning appears.
Warning: When the product is not used for a long period (more than 15 days),
remove the batteries. Otherwise, malfunctions that may occur would be out of
warranty. Please throw your dead batteries into the waste bin for batteries.
Thermostat wiring diagram
E
1: Heating/Cooling unit
Warning: Operations within the heating / cooling unit or the electrical installation
must be carried out by professionally qualified persons.
Thermostat temperature calibration: Temperature sensors which are used in
Thermostats are highly sensitive. You may need to calibrate your Thermostat if
you would like to get the same temperature values with other thermometers in
your living space.
• While your device is turned off, press and hold the "On/Off"button for 3 seconds.
• Press the "On/Off" button until the "
desired temperature, set the temperature difference by press the "Temperature
Adjustment Buttons". This value can be arranged between "-8oC" and "+8oC".
• To save the settings and exit, press the "On / Off" button or wait 10 seconds until
the device turns off.
Note: Recommended tempreture calibration is "0,0ºC"
Thermostat heating / cooling modes: Your Thermostat has heating and cooling
modes. In order to switch easily between heating and cooling modes:
• While your device is turned off, press and hold the "On/Off" button for 3 seconds.
• Press the "On / Off" button until the "
• You can switch between "
" (heating) y "
" or " " buttons in the "
• To save the settings and exit, press the "On / Off" button or wait 10 seconds
until the device turns off.
• The settings you have made have been saved. Once you turned on your
device, it will operate with the changed settings.
Thermostat hysteresis positive menu: Hysteresis positive factory setting of your
thermostat is 0,5°C. This value may be adjusted between "0,1°C" and "2,0°C". While
hysteresis positive value 0,5°C, if the room temperature goes above 0,5°C of set
temperature, your thermostat will send a signal to your heating/cooling unit.
For instance, when you set your thermostat to 22°C if the room temperature goes
above 22,5°C, on heating mode your heating unit will stop working; on cooling mode
your cooling unit will start working. In order to change the hysteresis positive setting:
• While your device is turned off, press and hold the "On/Off"button for 3 seconds.
• Press the "On/Off" button until "
• Adjust the operating sensitivity by using " " and " " buttons in the "
hysteresis positive menu.
• To save the settings and exit, press the "On / Off" button or wait 10 seconds
until the device turns off.
• Changes have been saved. Your thermostat will be working with set operating
sensitivity when you open your device.
• ON/OFF Control
• Wired Connection
• Hysteresis Settings
" menu appers. In order to see the
" menu appears..
" (cooling) modes by using the "
" menu.
" menu appears.
Thermostat hysteresis negative menu: Hysteresis negative factory setting of
your thermostat is -0,5°C. This value may be adjusted between "-0,1°C" y "-2,0°C".
While hysteresis negative value is -0,5°C, if the room temperature goes below 0,5°C
of set temperature, your thermostat will send a signal to your heating/cooling unit.
For instance, when you set your thermostat to 22°C if the room temperature goes
below 21,5°C, on heating mode your heating unit will start working; on cooling mode
your cooling unit will stop working. In order to change the hysteresis negative setting:
• While your device is turned off, press and hold the "On/Off"button for 3 seconds.
• Press the "On/Off" button until "
• Adjust the operating sensitivity by using " " and " " buttons in the "
hysteresis negative menu.
• To save the settings and exit, press the "On / Off" button or wait 10 seconds
until the device turns off.
• Changes have been saved. Your thermostat will be working with set operating
sensitivity when you open your device.
Factory settings reset: You can reset your Thermostat to its default factory
settings. This operation resets the mode temperature values, calibration setting,
heating/coling modes and hysteresis settings to factory setting. To reset your
Thermostat to factory setting:
• While your device is turned off, press and hold the "On/Off"button for 3 seconds.
• Press the "On/Off" button until "
• While in the "
" menu, select the " " option by using " " or " " buttons
and press the "On/Off" button.
• Your device will be turned off and reset to factory settings.
Key lock: In the Thermostat there is a key lock function to avoid any unintended
contact. In order to unlock the Thermostat's key lock "Mode" button should be
pressed for 3 seconds. If buttons on Thermostat are not touched for 10 seconds,
key lock will be reactivated.
Day and hour settings
• While your Thermostat is on, keep pressing "Weekly Program" button for 3 seconds.
• At the first screen that appears "Hour" part will be blinking. You may set the
time with " " and " " buttons.
• After setting the time, ''Settings'' button needs to be pressed once. For
minute setting, minute part will be blinking. You may set the minute with "
" and " " buttons.
• After setting the minute, ''Settings'' button needs to be pressed once to set
the day of the week.
• Monday has set as the first day of the week and indicated with number "1".
• Numbers indicates the following days respectively 2-Tuesday, 3- Wednesday,
4-Thursday, 5-Friday, 6-Saturday and 7-Sunday
• When setting is done you may exit by pressing for 3 seconds to "Weekly
Program" button.
Mode settings: Your Thermostat has 4 different modes. Two of them(Comfort
F
and Economy Mode) are preset modes. Other modes are manual mode and
programming mode. In preset modes, temperature values are based on the user's
choices which have been set in the beginning. Manual mode allows the Thermostat
to operate within the temperature which is required and set directly by user. Weekly
Program mode continues to work according to the weekly schedule determined by
the user. In order to change the temperature values of preset modes:
• Press and hold the "Setting" button for 3 seconds while your Thermostat is on.
• Comfort Mode temperature value will appear. You may adjust the temperature
value of Comfort Mode by pressing the " " and " " buttons.
• When setting is done, you may adjust the temperature value of Economy
Mode with the " " and " " buttons by pressing the "Mode" button.
• You may exit the setting screen by pressing the "Setting" button for 3 seconds.
• In order to change the manual mode temperature, press the " " or " "
button while in the main screen. The Thermostat will switch to Manual Mode
once pressed the " " or " " button.
• You may press the "Mode" button to switch to the other modes.
Weekly Program: You may set the operating schedule of your Thermostat with weekly
program mode. 7 different temperature values can be set for each day in weekly
programming. These values can be set in temperature adjustment screens ''P0-P6''.
• In order to set the weekly schedule, press and hold the "Weekly Program"
button for 3 seconds while your Thermostat is on. The "Hour, Minute and
Day" setting will appear. Press the "Settings" button until the "Weekly
Program" menu (P0) appears.
• Days of the week will be blinking on the screen. You can initiate the weekly
program setting if you wish to set the same schedule for every day of the week.
• Press the " " button once if you wish to set the same schedule for the
weekdays. First five days of week will be blinking on the screen.
• Press the " " button once more if you wish to set the same schedule only for
the weekend. Last two days of the week will be blinking on the screen.
• Press the " " button one more time if you wish to set a different schedule
for each day of the week. 1st day of the week will be blinking on the screen.
You can switch between the days by pressing the " " button. Press the " "
button in order to switch to the previous day.
• Press the "Weekly Program" button once to set a schedule. "P0" will be
blinking on the screen. Set the temperature value of "P0" by pressing the
"Weekly Program" button once more. The hour setting of "P0" cannot be
changed since it's factory setting.
• Press the "Weekly Program" button again. Day indicator will be blinking. If
you will not change the day, press the "Weekly Program" button again and
switch to the "P1" setting by pressing the " " button.
• First, hour setting will appear on the screen. Once you complete the hour setting,
adjust the minute setting by pressing the "Weekly Program" button. After the
minute setting, press the "Weekly Program" button to set the temperature value.
• Follow the same steps for other schedule settings.
• Once all changes made, press and hold the "Weekly Program" button for 3
seconds to save.
Note: In order to check the weekly schedule which has been set without making
any changes, press the "Weekly Program" button once while your Thermostat is
on. Press the " " and " " buttons to see the days, press the "Mode" button to
see the settings between "P0-P6".
"
Thermostat working logic
Heating Mode: Your thermostat takes the average room temperature of last
G
40 seconds as basis. If the room temperature goes above the hysteresis positive
temperature value you set, your Thermostat will stop the heating unit. If it goes below
the hysteresis negative temperature value, your Thermostat will start the heating
unit. Thus, it ensures that the room temperature remains within a certain range.
6
" menu appears.
" menu appears.
"
Publicidad
