Descargar Imprimir esta página
Broan MD6TU Manual Del Usuario
Broan MD6TU Manual Del Usuario

Broan MD6TU Manual Del Usuario

Regulador de aire automatico de repuesto,con transformador e interruptor de presion
Ocultar thumbs Ver también para MD6TU:

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

BROAN
MODELS
MD6TU « MD8TU
AUTOMATIC MAKE-UP AIR
DAMPER WITH TRANSFORMER
& PRESSURE SWITCH
To register this product
visit: www.broan.com
A
FOR RESIDENTIAL USE ONLY A
WARNING
&
ha
CAUTION
A
TO
REDUCE
THE
RISK
OF
FIRE,
ELECTRIC
SHOCK,
OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1.
10.
11.
12.
13.
14.
Installation work and electrical wiring must be done by a qualified
person(s) in accordance with all applicable codes and standards,
including fire-rated construction codes and standards.
Do not use the unit in conjunction with any exhaust device other
than compatible BEST, Broan Elite or Broan range hoods.
This unit is not designed to provide combustion air for fuel-
burning appliances.
Do not connect the unit directly to a combustion appliance of
any type.
Sufficient air is needed for proper combustion and exhausting
of gases through the flue (chimney) of fuel burning equipment
to
prevent
backdrafting.
Follow
the
heating
equipment
manufacturer's guideline and safety standards such as those
published by the National Fire Protection Association (NFPA),
and
the American
Society
for Heating,
Refrigeration
and
Air Conditioning
Engineers
(ASHRAE),
and the local code
authorities.
Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting
means
cannot
be
locked,
securely fasten
a
prominent warning device, such as a tag, to the service panel.
When performing installation, servicing or cleaning the unit, it is
recommended to wear safety glasses and gloves.
During extreme weather events including snow storms, ensure
that the intake area for the outside air duct is not blocked and
able to provide a clear pathway for outside air to enter the
system.
When
cutting or drilling into wall or ceiling, do not damage
electrical wiring or other hidden utilities.
When notching or drilling into framing including floor supports,
rim joists, and wall studs, comply with code and manufacturer
limitations
on
allowable
modifications
to
these
structural
members.
This unit is intended to be installed within the home in a location
protected from moisture.
This unit must be in an accessible
location which
allows for
inspection of the unit.
Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer at the address
or telephone number listed in this document.
When federal, provincial or state legislation comprises more
restrictive
installation
and/or
certification
requirements,
the
aforementioned requirements prevail on those of this document
and the installer agrees to conform to these at his own expense.
1.
Do not locate outside airinlet near hazardous materials or explosives.
2. Unit shall not be installed to introduce air from crawlspaces, garages,
attics, adjacent dwelling units, or other locations within the building
shell. Unit shail be installed to introduce air directly from outdoors.
3. Do not run the outside air duct directly above or closer than 2 ft to
any furnace or its supply plenum, boiler, or other heat producing
appliance.
4. Any ductwork used in conjunction with the Damper must be installed
in compliance with all local and national codes that are applicable.
5. Do not operate the Damper for fresh air introduction until all system
filters, including the central duct system filter, have been installed per
the system design.
6. Please read the unit specification label on the product for further
information and requirements.
7.
The Damper's outdoor air intake, ducting, and any filters should be
inspected and maintained on a regular basis.
8. Insulate the duct and damper to prevent build-up of condensation in
cold weather climates. Vapor barriers on both sides of insulation are
recommended.
WARRANTY
BROAN-NUTONE ONE YEAR LIMITED WARRANTY
Broan-NuTone warrants to the original consumer purchaser of its products that such prod-
ucts will be free from defects in materials or workmanship for a period of one year from the
date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.
During this one-year period, Broan-NuTone will, at its option, repair or replace, without
charge, any product or part which is found to be defective under normal use and service.
THIS WARRANTY
DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS, TUBES,
HALOGEN AND INCANDESCENT BULBS, FUSES, FILTERS, DUCTS, ROOF CAPS, WALL
CAPS AND OTHER ACCESSORIES FOR DUCTING. This warranty does not cover (a) normal
maintenance and service or (b) any products or parts which have been subject to misuse,
negligence, accident, improper maintenance or repair (other than by Broan-NuTone), faulty
installation or installation contrary to recommended installation instructions.
The duration of any implied warranty is limited to the one-year period as specified for the
express warranty. Some states do not allow limitation on how long an implied warranty
lasts, so the above limitation may not apply to you.
BROAN-NUTONE'S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE'S OPTION,
SHALL BE THE PURCHASER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY.
BROAN-NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL
DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE.
Some states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary
from state to state. This warranty supersedes all prior warranties.
To qualify for warranty service, you must (a) notify Broan-NuTone at the address or telephone
number below, (b) give the model number and part identification and (c) describe the nature
of any defect in the product or part. At the time of requesting warranty service, you must
present evidence of the original purchase date.
Broan-NuTone LLC, 926 W. State Street, Hartford, Wisconsin 53027
www.broan.com
800-558-1711

Publicidad

loading

Este manual también es adecuado para:

Md8tu