urmet domus Digivoice 1138/18 Manual De Instrucciones página 8

This function is switched on/off by means of button
(10). When the MUTE function is on, LED (11) will
be on with fi xed green light and all calls will be
inhibited.
ress (1 ) to out ut a door o ener code
accom anied by a courtesy tone on the s ea er.
The door in the system will be o ened according
to the rogramming (ty ically, the door where the
s ea er connected to the s ecial door
connected).
A A
This function is used to automatically out ut a door
o ening signal when called. Sim ly ress S
MUTE ( )-(10) to switch the function on or off. LED
(11) will ash with green light when the function is
on. b iously the function can be on regardless of
the MUTE function.
To switch the function on without MUTE,
S T-MUTE. LED (11) will ash. When called, the
door hone will ring and the door o ener code will
be out ut. To switch the function off, ress S
MUTE again. The LED (11) will go out.
To switch the function on with MUTE, ress MUTE.
LED (11) will come with fi xed green light.
S T-MUTE again. LED (11) will ash. When
called, the door hone will not ring and will out ut
the door o ening signal. To switch the function off,
ress S T-MUTE again LED (11) will remain on
with green light while the MUTE function is still on.
ress MUTE to switch it off.
A
LED (14) can be off, fi xed or ashing. The LED
will be on fi xed to indicate that one or more of the
main doors are o en. t will ash to indicate that the
secondary door is o en.
The LED will ash in any case if the secondary and
at least one main door are o en at the same.
A
An audio- ideo communication can be established
with a main calling station or the res ecti e
secondary station.
To wa e u from main station lift the handset,
enter the main station code and ress (13). A
communication will be established directly with the
module if the selected main station is standing by.
14
To wa e u from secondary station
handset off or on hoo . The o eration outcome will
be ositi e if the secondary station is standing by.
Wake up from secondary is not possible in
system fi tting two secondary stations in a
cascade on the same column.
Wake up from pre-programmed main stations
is possible if the special door phone is
confi gured according to the "PROGRAMMED"
call method (see CONFIGURATION). In this
case, simply lift the handset, press the
programmed button and press (4) to confi rm.
hone is
A
odes for s ecial ser ices can be sent. Lift the
handset, enter the ser ice code (0
characters) and ress (4). f the code corres onds
T- to a sensor reading code, sensor status information
will a ear
1 EE
3 EE S .
ress Pre-programmed special codes can be sent if
the special door phone is confi gured according
to the "PROGRAMMED" call method (see
T- CONFIGURATION). In this case, simply lift
the handset, press the programmed button
and press (4) to confi rm.
ress
A
The s ecial door hone can be used to call the
decoders and inform the o eration outcome, that is
1 EE
3 EE S .
To program column code X1 or X2 in a
decoder, enter 1 followed by SHIFT-CALL or
2 followed by SHIFT-CALL.
A A
LED (11) will ash with red and green light when the
data line is either short-circuited or not connected.
ress (13) with A
A A A A
learance
Dimensions (mm) 90x220x67mm
Materials
o er
ase
andset
olour
eyboard
A
u to three
Tem erature range
umidity
A
ower oltage range (
Maximum stand-by
inta e ( 0 )
Maximum inta e (
nta e in terms of UL
and signal out ut
Maximum a licable oltage
Maximum inta e current
S ecial door hone 1138/18 com lies with the
following standards
E E 0081-1
(residential and light industrial en ironments).
E E 0082-1
(residential and light industrial en ironments).
DS1138-002 DS1138-002
A
A S
A S
A S
White
17 buttons
A
- 4
9 30
A
0 ) 16 -2 .2 D
60 mA
0 ) 4 0 mA
4 UL
30 D
10 mA
A A
eneral emissions standard
eneral immunity standard
1