Fein ASAS18-21KAS Manual Del Usuario página 16

1 609 92A 875 • 27.10.22 • T
en
16
Reciprocating saw
Recommended char-
gers
A) Measured at 20–25 °C with rechargeable battery
GBA 18V 4.0Ah.
B) Depends on battery in use
C) Limited performance at temperatures < 0 °C
Noise/vibration information
Noise emission values determined according to
EN 62841‑2‑11.
Typically, the A-weighted noise level of the
power tool is: Sound pressure level 82 dB(A);
sound power level 93 dB(A). Uncertainty
K = 5 dB.
Wear hearing protection!
Vibration total values a
uncertainty K determined according to
EN 62841‑2‑11:
Cutting boards with saw blade HCS, 150 × 19 ×
1,25 mm, 6 TPI:
2
a = 9 m/s , K = 1.5 m/s
h,B
Cutting wooden beams with saw blade BIM,
150 × 19 × 1,25 mm, 6 TPI:
2
a = 8 m/s , K = 1.5 m/s
h,WB
(The specifications for cutting boards apply to a
workpiece thickness of 20 mm.)
The vibration level and noise emission value
given in these instructions have been measured
in accordance with a standardised measuring
procedure and may be used to compare power
tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission
value represent the main applications of the
power tool. However, if the power tool is used
for other applications, with different application
tools or is poorly maintained, the vibration level
and noise emission value may differ. This may
significantly increase the vibration and noise
emissions over the total working period.
To estimate vibration and noise emissions accur-
ately, the times when the tool is switched off or
when it is running but not actually being used
should also be taken into account. This may sig-
nificantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect
the operator from the effects of vibration, such
as servicing the power tool and application tools,
keeping their hands warm, and organising work-
flows correctly.
ASAS18-21KAS
GAL 18...
English
(triax vector sum) and
h
2
,
2
.
Rechargeable battery
Charging the battery
English
Use only the chargers listed in the technical
u
data. Only these chargers are matched to the
lithium-ion battery of your power tool.
Note: Lithium-ion rechargeable batteries are
supplied partially charged according to interna-
tional transport regulations. To ensure full re-
chargeable battery capacity, fully charge the re-
chargeable battery before using your tool for the
first time.
Inserting the Battery
English
Push the charged battery into the battery holder
until it clicks into place.
Removing the Battery
To remove the rechargeable battery, press the
battery release button and pull the battery out.
Do not use force to do this.
The rechargeable battery has two locking levels
to prevent the battery from falling out if the bat-
tery release button is pressed unintentionally.
The rechargeable battery is held in place by a
spring when fitted in the power tool.
Battery charge indicator
The green LEDs on the battery charge indicator
indicate the state of charge of the battery. For
safety reasons, it is only possible to check the
state of charge when the power tool is not in op-
eration.
Press the button for the battery charge indic-
ator or to show the state of charge. This is
also possible when the battery is removed.
If no LED lights up after pressing the button for
the battery charge indicator, then the battery is
defective and must be replaced.
Battery model GBA 18V...
LED
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Battery model ProCORE18V...
LED
5 × continuous green light
4 × continuous green light
English
English
English
English
Capacity
60–100 %
30–60 %
5–30 %
0–5 %
English
Capacity
80–100 %
60–80 %